C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System Secondary Filter - Replace Caterpillar


Fuel System Secondary Filter - Replace
`
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines [SEBU7605]
FUEL SYSTEM
FILTER GP-FUEL
3054E and 3056E Industrial Engines Fuel System Primary Filter/Water Separator - Drain
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System Secondary Filter - Replace
1.1. Fuel Filter With Canister
2.1. Fuel Filter With Element

------ WARNING! ------

Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.



NOTICE

Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Dispose of all fluids according to local regulations and mandates.


Fuel Filter With Canister

  1. Close the fuel supply valve.


    Illustration 1g01122129

  2. Clean the outside of the fuel filter assembly.

  3. Open the fuel drain (2) in the bottom of the filter assembly, if equipped. Drain the fuel into a suitable container.

  4. Loosen the setscrew (1).

  5. Remove the canister (3).


    Illustration 2g00917937

  6. Assemble the following items: seals (8), seal (7), canister (9) and base (10). Place washer (5) and seal (6) on setscrew (4).

  7. Fasten the assembly to the fuel filter base with setscrew (4).

The fuel system will need to be primed after the new filter is installed. Refer to this Operation and Maintenance Manual, "Fuel System - Prime".

Fuel Filter With Element

  1. Close the fuel supply valve (1).


    Illustration 3g01122130

  2. Clean the outside of the fuel filter assembly.

  3. Loosen the locking ring (3).

  4. Remove the casing for the filter (2) and the element.


    Illustration 4g01122131

  5. Assemble the following items: seal (5), filter element (6) and casing (7).

  6. Install the assembled items to the filter head (4).

  7. Install the locking ring (8) to the filter head. Rotate the locking ring in order to lock the assembly.

The fuel system will need to be primed after the new filter is installed. Refer to this Operation and Maintenance Manual, "Fuel System - Prime".

Information System:

C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System - Prime
3508B, 3512B and 3516B Generator Set Engines Engine Oil Pan - Install
3508B, 3512B and 3516B Generator Set Engines Engine Oil Pan - Remove
C32 Marine Engines Fuel System
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Turbocharger - Inspect - If Equipped
2004/12/01 Improved Alignment of a Coolant Tube {1380}
C9 Industrial Engines Cooling System
C27 and C32 Engines Finding Top Center Position for No. 1 Piston
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Crankcase Breather - Replace
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator and Fan Belts - Inspect/Adjust
C7 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C7 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
3508B, 3512B and 3516B Generator Set Engines Crankshaft - Remove
3508B, 3512B and 3516B Generator Set Engines Crankshaft - Install
3126B Petroleum Engine Sensors and Electrical Connectors
3126B Petroleum Engine Cooling System
Installation of 244-1090 Alarm Gp {7400, 7402, 7407}
3500 and 3500B Engines Refill Capacities and Recommendations
C27 and C32 Engines Water Pump - Test
3500B High Displacement Generator Set Engines Alternator and Fan Belts - Inspect/Adjust/Replace
C7 On-Highway Engine Engine Oil Filter Base and Oil Cooler - Remove
345C MHPU Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Swing)
2004/12/01 New Ignition Transformers are Used {1561}
C27 and C32 Engines Fuel System Pressure - Test