Retrofit SCR Aftertreatment Exhaust Outlet Nitrogen Oxide Sensor - Inspect/Replace Caterpillar


Exhaust Outlet Nitrogen Oxide Sensor - Inspect/Replace
`
Retrofit SCR Aftertreatment [SEBU9148]
ELECTRICAL AND STARTING SYSTEM
SENSOR GP
Retrofit SCR Aftertreatment Exhaust Outlet Nitrogen Oxide Sensor - Inspect/Replace





Illustration 1g03669956

Note: During installation, inspection, and handling of the sensor, follow the parameters listed below:

Note: Turn off power supply before disconnecting or connecting the NOx sensor.

  • Inspect harness for damaged wiring

  • Inspect for secure connections at all ends of the harness

  • Do not contact the sensing element when power is applied to the sensor. Contact with the sensing element may result in injury. The sensing element is heated to a minimum of 100° C (212° F).

  • Do not use any lubricant on any part of the sensor other than the threads. Do not use unapproved thread lubricant. Do not apply additional anti-seize to new parts. If additional anti-seize is necessary for pre-installation, use only nickel based anti-seize or non-metallic anti-seize. Apply anti-seize to the threads only and avoid contaminating the sensor head.

  • Do not use sensors that have been dropped or have been exposed to other forms of mishandling. Damage to the sensor may have occurred that is not visible.

  • Replace the sensor if damaged or faulty.

To replace the NOx sensor, follow the steps listed below:

  1. Disconnect harness assembly and disconnect sensor cabling.

  1. Remove NOx sensor probe.



    Illustration 2g02715050

  1. Install outlet NOx sensor probe. Take precautions to prevent damaging the ceramic sensor element (4) when installing.

  1. Ensure that the sensor is securely mounted.

  1. Connect harness assembly and cabling.

  1. Install cover plate assemblies and bolts. Refer to Specifications, SENR3130, "Torque Specifications" for the proper torque.

Information System:

EMCP4.1/EMCP4.2 Integrated Voltage Regulator
Retrofit SCR Aftertreatment Catalyst (SCR) - Replace
C18 Petroleum Engine Monitoring System
C18 Petroleum Engine Gauges and Indicators
14L Motor Grader Machine Systems Centershift Lock Bar and Bushings - Remove
C18 Petroleum Engine Product Description
14L Motor Grader Machine Systems Centershift Lock Bar and Bushings - Install
Bench Test Procedure for a CX31 On Highway Truck or AD22 Articulated Truck Transmission {3030, 3073}
Disassembly and Assembly Procedure for 3N-8891 Sea Water Heat Exchanger Gp {1379}
C18 Petroleum Engine Maintenance Interval Schedule
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Electrical Connections
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders Brake Control Valve (Service)
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders Brake Accumulator
Retrofit SCR Aftertreatment Catalyst (DOC) - Replace
Retrofit SCR Aftertreatment Diesel Particulate Filter - Replace
2013/11/21 New Engine Software is Now Used on Certain C32 Marine Engines {1901, 1920}
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines
C4.4 Industrial Engine Coolant (Commercial Heavy-Duty) - Change
C4.4 and C7.1 Engines Fuel Rail Pressure Problem
C7 Petroleum Engine Product Description
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders Service Brakes
C7 Petroleum Engine Refill Capacities