Model View Illustrations
` Show/hide table
| |
| Illustration 1 | g02856099 |
|
View of the right side of a typical 3500 C Marine Engine (1) Exhaust outlet (2) Heat shield for the turbochargers and for the exhaust outlet elbow (3) Exhaust bypass valve (4) Fumes disposal filters (5) Engine crankcase breathers (6) Heat shield for the aftercoolers (7) Engine oil filter (8) Fuel filter (9) Expansion tank (10) Engine oil sampling valve (11) Engine oil pump (12) Engine oil cooler (13) Engine oil level gauge (14) Power distribution box (15) Engine air cleaner | |
Show/hide table
| |
| Illustration 2 | g02856101 |
|
View of the left side of a typical 3500 C Marine Engine (16) Filler cap for the expansion tank (17) Cover for the electronic control module (ECM) (18) Water temperature regulator (19) Water pump (20) Auxiliary water pump (21) Cover group for the ECM | |
Show/hide table
| |
| Illustration 3 | g02963039 |
|
View of the rear of a typical 3500 C Marine Engine (22) Turbochargers | |
Show/hide table
| |
| Illustration 4 | g03470978 |
|
Dosing Control Cabinet (1) Service tool connector (2) Electrical harness connection to engine ECM (3) Electrical harness connection to DEF tank (4) Electrical harness connection from CEM to dosing cabinet (5) DEF vent port (6) 120 V AC source (7) DEF outlet to CEM (8) DEF inlet/strainer (9) Air outlet to CEM (10) Air inlet/strainer | |
Show/hide table
| |
| Illustration 5 | g03523614 |
|
U-Flow Reactor Housing (1) Outlet spool (2) DEF injector (3) Inlet spool (4) Inlet sensor box (5) Lifting eyes (6) Catalyst access cover (7) Outlet sensor box (8) Mounting brackets | |
Show/hide table
| |
| Illustration 6 | g03535445 |
|
Z-Flow Reactor Housing (1) Outlet spool (2) DEF injector (3) Inlet spool (4) Inlet sensor box (5) Lifting eyes (6) Catalyst access cover (7) Outlet sensor box (8) Mounting brackets | |
Information System:
Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479}
3516C Marine Engine
Catalyst (SCR) - Replace
C280-16 Engine
Exhaust Manifold Shield - Remove and Install
C15 and C18 On-Highway Engines
Cylinder Head - Remove and Install
C15 and C18 On-Highway Engines
Rocker Arm and Shaft - Remove and Install
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and 160 Motor Graders
Solenoid Valve - Test
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders
Hydraulic System
C15 and C18 On-Highway Engines
Crankshaft Front Seal - Remove and Install
C15 and C18 On-Highway Engines
Power Take-Off Drive Group - Assemble
C15 and C18 On-Highway Engines
Flywheel Housing - Remove and Install - Power Take Off equipped
C280 Marine Engines
Battery
CX31-P600 Petroleum Transmission
Hydraulic Oil Contamination - Test
C15 and C18 On-Highway Engines
Camshaft - Remove and Install
C15 and C18 On-Highway Engines
Camshaft - Remove and Install
C13, C15, and C18 Tier 4 Final Engines
Water in Fuel - Test
C15 and C18 On-Highway Engines
Engine Oil Pan - Remove and Install
TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400}
C11 and C13 Engines for Caterpillar Built Machines
Valve Actuator (Variable) - Remove and Install
140, 150, 160, 12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders
Service Interval Chart
C175 Oil Pressure Regulator Inspection and Rework{1304, 5117}
793F Tier IV Off-Highway Truck Field Assembly
Films - Install
793F Tier IV Off-Highway Truck Field Assembly
Wheel Chock - Install
C280-08 Marine Engine
Plate Locations and Film Locations
C15 and C18 On-Highway Engines
Vibration Damper and Pulley - Remove and Install