3516C Marine Engine Product Lifting Caterpillar


Product Lifting
`
2.1. Engine Lifting
3.1. Engine and Marine Transmission Lifting
4.1. Marine Transmission Lifting
5.1. Aftertreatment Component Lifting
6.2. SCR Reactor Housing
7.2. Lifting the Dosing Cabinet

Engine Lifting




Illustration 1g01020684

------ WARNING! ------

Improper lift rigging can allow unit to tumble causing injury and damage.

----------------------



Illustration 2g02858678


NOTICE

Never bend the eyebolts and the brackets. Only load the eyebolts and the brackets under tension. Remember that the capacity of an eyebolt is less as the angle between the supporting members and the object becomes less than 90 degrees.

When it is necessary to remove a component at an angle, only use a link bracket that is properly rated for the weight.


Use a hoist to remove heavy components. Use an adjustable lifting beam to lift the engine. All supporting members (chains and cables) should be parallel to each other. The chains and cables should be perpendicular to the top of the object that is being lifted.

Some removals require lifting fixtures in order to obtain proper balance. Lifting fixtures also help to provide safety.

To remove the engine ONLY, use the lifting eyes that are on the engine.

Lifting eyes are designed and installed for the specific engine arrangement. Alterations to the lifting eyes and/or the engine make the lifting eyes and the lifting fixtures obsolete. If alterations are made, ensure that proper lifting devices are provided. Consult your Cat dealer for information regarding fixtures for proper engine lifting.

Table 1
Dimensions for the Lifting Beam    
Engine     A     B     C    
3512    
1096 mm (43.0 inch)    

1652 mm (65.0 inch)    
12° Max    
3516    
1096 mm (43.0 inch)    

2192 mm (86.3 inch)    
12° Max    

Table 2
Engine Weight    
Engine     Approximate Net Dry Engine Weight Without Transmission    
3512C     7445 kg to 7670 kg     16415 lb to 16910 lb    
3516C     8900 kg to 9400 kg     19625 lb to 20725 lb    

Engine and Marine Transmission Lifting




Illustration 3g00103228


NOTICE

Do not use the eyebolts that are on the marine transmission housing to lift the engine.


To remove both the engine and the marine transmission, use the lifting eyes that are on the engine. Use an adjustable lifting beam to lift the engine. All supporting members (chains and cables) should be parallel to each other. The chains and cables should be perpendicular to the top of the object that is being lifted. Consult your Cat dealer or consult the OEM for information regarding fixtures for proper lifting of your complete package.

Marine Transmission Lifting

To remove the marine transmission ONLY, use the eyebolts that are on the marine transmission housing. Refer to the OEM for proper lifting instructions (if equipped).

If a component resists removal, ensure that all of the nuts and bolts have been removed. Ensure that no adjacent parts are interfering.

Aftertreatment Component Lifting

------ WARNING! ------

Improper lift rigging can allow unit to tumble causing injury and damage.

----------------------

Refer to the Application and Installation Guide for additional information on lifting aftertreatment components.

SCR Reactor Housing




Illustration 4g03535936

Attach appropriately lifting equipment to the lifting eyes located at each corner of the SCR reactor housing. Ensure that lifting equipment is clear of all sensors and fittings prior to lifting. Do not use reactor housing mounting feet to lift the SCR reactor housing.

Depending on the installation configuration of your CEM, the lifting links may be installed in alternative locations. Spreader bars may be required from some lifting configurations. If necessary, the inlet and outlet spool may be removed to allow clearance to the lifting links. Consult your Cat dealer for detailed procedures.

The CEM should not be lifted with a fork lift after the CEM has been removed from the original shipping pallet.

Lifting the Dosing Cabinet




Illustration 5g03493658

Dosing cabinet lifting slots

Insert the appropriate lifting straps through the lifting slots, as indicated, in the base of the dosing cabinet.

Table 3
Dosing Cabinet Dimensions    
Length    
1010 mm (39.8 inch)    
Width    
553 mm (21.7 inch)    
Height    
634 mm (25 inch)    
Weight without DEF    
95 kg (209.4 lb)    

Information System:

G3600 A4 Engines Fuel Temperature Is High
G3600 A4 Engines Electrical Power Supply - Test
New IGBT Driver For UPSB505 {1401, 4480}
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Modulating Valve (Transmission Hydraulic Control)
G3600 A4 Engines Alternator Problem - Charging Problem and/or Noisy Operation
C13, C15, and C18 Tier 4 Final Engines Exhaust Combustion (ARD)
G3600 A4 Engines Exhaust Temperature Is Low
16M Series 3, 16, 18M Series 3 and 18 Motor Grader Power Train System
G3600 A4 Engines Exhaust Temperature Is High
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism Cover
C13, C15, and C18 Tier 4 Final Engines Turbocharger
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders Electronic Control (Power Train System)
3500E Marine Engines Alarms and Shutoffs
2013/12/18 New Main Rotor, Bearing Sleeve, Bearing Retainer Bar, And Cable Lugs Are Now Available For Gas Generator Sets Packaged With 2650 Frame High Voltage Generators {4459, 5258}
HI315B Injector System Priming{1256, 1258}
2014/02/21 New Software Is Used For Certain C280 Marine Engines {1902, 1920}
Wear on Swash Plate Support in Side By Side Pumps on Certain Excavators{5070}
Replacement of the Clean Emissions Module on Certain 3516C and 3516C HD Generator Set Engines{1091}
3516C Marine Engine Product Description
3500E Marine Engines Before Starting Engine
Procedure for Replacing the Turbine Inlet Bellows on Certain C175 Engines {1061}
3500E Marine Engines Fluid Recommendations
C13, C15, and C18 Tier 4 Final Engines Turbocharger
C13, C15, and C18 Tier 4 Final Engines Fuel Manifold (ARD)