345C Excavator Machine System Specifications Stick - 3.0 m (9.84 ft) Caterpillar


Stick - 3.0 m (9.84 ft)
`


Illustration 1g02882356
Right side view

Table 1
Specification for 228-5440 Hoe Stick Gp 
Item  Qty  Part  Specification Description 
All bores must be free of paint. Use 5P-0960 Grease Cartridge in order to coat all bores for the pins, the bucket, the bushings, and the cylinder pin bores. After you assemble the bushings, coat all the bores and the bushings with 5P-0960 Grease Cartridge. 
The stick cylinder must be assembled in order to orient the grease zerk, as shown in Illustration 1. 
Install one shim and one spacer to the bracket that is next to each bucket cylinder, as shown in Illustration 1: 
2 133-2427 Shim  Thickness is 0.5 mm (0.02 inch)
2 134-8944 Spacer  Thickness is 5.0 mm (0.20 inch)
130-4360 Pin As  Diameter is 99.85 ± 0.04 mm (3.931 ± 0.002 inch)
As required, use the following shims to adjust the maximum lateral clearance of 1.0 mm (0.04 inch)
1 133-2427 Shim  Thickness is 0.5 mm (0.02 inch)
2 093-0090 Shim  Thickness is 1.0 mm (0.04 inch)
1 093-0122 Shim  Thickness is 2.0 mm (0.08 inch)
As required, use the following shims to adjust the maximum lateral clearance of 1.0 mm (0.04 inch)
1 133-2427 Shim  Thickness is 0.5 mm (0.02 inch)
2 093-0090 Shim  Thickness is 1.0 mm (0.04 inch)
1 093-0122 Shim  Thickness is 2.0 mm (0.08 inch)
166-1494 Lip Type Seal  Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. 
9X-4599 Lip Type Seal  Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. 
228-5621 Bushing(1)  Bore before assembly is 120.259 ± 0.040 mm (4.7346 ± 0.0016 inch).
Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch)
462-2005 Bushing(1)  Bore before assembly is 80.181 ± 0.020 mm (3.1567 ± 0.0008 inch).
Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch)
(1) Install the bushing in the bore so that the part number of the bushing is facing outward.

Information System:

345C Excavator Machine System Specifications Stick
345C Excavator Machine System Specifications Stick
3500 and 3500B Engines Reference Numbers
3126B Petroleum Engine Injection Actuation Pressure - Test
G3520C and G3520E Generator Set Engines Fuel Control Valve - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Lubrication System
C11 and C13 Engines for Caterpillar Built Machines General Information
C4.4 Industrial Engine Electrical System
2004/12/01 New Lockwasher Will Improve Varistor Reliability {4466}
3508B, 3512B and 3516B Generator Set Engines Flywheel Housing - Install
3508B, 3512B and 3516B Generator Set Engines Flywheel Housing - Remove
12M, 140, 140M, 150, 160M and 160 Motor Graders Hydraulic and Steering System Calibration Procedures
Installation of 262-6141 Alarm Gp {7406}
2004/12/01 Lifting Brackets and Hardware are Available {1122}
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
3508C, 3512C and 3516C Marine Engines Piston Cooling Jets - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
345C Excavator Machine System Specifications Stick - 3.4 m (11.16 ft)
3408C and 3412C Marine Auxiliary and Marine Generator Set Engines Refill Capacities and Recommendations