345C Excavator Machine System Specifications Stick - 3.4 m (11.16 ft) Caterpillar


Stick - 3.4 m (11.16 ft)
`


Illustration 1g02882200
Right side view

Table 1
Specification for 290-9138 Hoe Stick Gp, 297-7443 Hoe Stick Gp, and 297-7422 Hoe Stick Gp 
Item  Qty  Part  Specification Description 
All bores must be free of paint. Use 5P-0960 Grease Cartridge in order to coat all bores for the pins, the bucket, the bushings, and the cylinder pin bores. After you assemble the bushings, coat all the bores and the bushings with 5P-0960 Grease Cartridge. 
Stick cylinder must be assembled in order to orient the grease zerk, as shown in Illustration 1. 
141-3550 Pin As  Diameter is 89.850 ± 0.025 mm (3.5374 ± 0.0010 inch)
As required, use the following shims to adjust the maximum lateral clearance of 1.0 mm (0.04 inch)
1 113-2127 Shim  Thickness is 0.5 mm (0.02 inch)
2 093-0084 Shim  Thickness is 1.0 mm (0.04 inch)
1 093-0116 Shim  Thickness is 2.0 mm (0.08 inch)
130-4360 Pin As  Diameter is 99.85 ± 0.04 mm (3.931 ± 0.002 inch)
As required, use the following shims to adjust the maximum lateral clearance of 1.0 mm (0.04 inch)
1 133-2427 Shim  Thickness is 0.5 mm (0.02 inch)
2 093-0090 Shim  Thickness is 1.0 mm (0.04 inch)
1 093-0122 Shim  Thickness is 2.0 mm (0.08 inch)
9X-4599 Lip Type Seal  Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. 
228-5621 Bushing(1)  Bore before assembly is 120.259 ± 0.040 mm (4.7346 ± 0.0016 inch).
Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch)
166-1494 Lip Type Seal  Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. 
462-2005 Bushing(1)  Bore before assembly is 80.181 ± 0.020 mm (3.1567 ± 0.0008 inch).
Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch)
10  9X-4598 Lip Type Seal  Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. 
11  228-5619 Bushing(1)  Bore before assembly is 110.222 ± 0.040 mm (4.3394 ± 0.0016 inch).
Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch)
(1) Install the bushing in the bore so that the part number of the bushing is facing outward.

Information System:

C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3508C, 3512C and 3516C Marine Engines Piston Cooling Jets - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
2004/12/01 Lifting Brackets and Hardware are Available {1122}
Installation of 262-6141 Alarm Gp {7406}
345C Excavator Machine System Specifications Stick - 3.0 m (9.84 ft)
345C Excavator Machine System Specifications Stick
3408C and 3412C Marine Auxiliary and Marine Generator Set Engines Refill Capacities and Recommendations
C32 Marine Engines Diagnostic Code Cross Reference
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Remove