345 MHPUC Mobile Hydraulic Power Unit Machine System Specifications Fuel Lines Caterpillar


Fuel Lines
`
345 MHPUC Mobile Hydraulic Power Unit Machine System Specifications [KENR7926]


Illustration 1g02903717
Left side view


Illustration 2g02903718
Rear view


Illustration 3g02903719
Front view

Table 1
Specification for 248-9354 Fuel Lines Gp 
Item  Qty  Part  Specification Description 
8T-4133 Nut  Torque to 30 ± 7 N·m (266 ± 62 lb in)
095-1386 Hose Clamp  Torque to 3.0 ± 0.4 N·m (26.6 ± 3.5 lb in)
29  8T-4137 Bolt  Torque to 30 ± 7 N·m (266 ± 62 lb in)
003-7764 Hose End  Apply black Loctite Gasket Maker #2 to the threads of the hose ends. 

Information System:

C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C7 Engines for Caterpillar Built Machines Water Pump - Test
3126B Industrial Engines E100 Low Engine Oil Pressure Warning
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines V-Belts - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Bearing Clearance - Check
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Swing) - Test and Adjust
3500 Engines Atmospheric Pressure Sensor - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
3126B Petroleum Engine ECM/Personality Module - Test
C7 Industrial Engine Engine Monitoring System (EMS)
C9 Industrial Engines Diagnostic Flash Code Retrieval
C32 Marine Engines Analog Sensor Supply Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Refrigerant Receiver-Dryer
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Evaporator Coil
3508C, 3512C and 3516C Marine Engines Turbocharger Outlet Pressure Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Coolant Temperature Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Turbocharger Inlet Pressure Sensor - Remove and Install
C7 Petroleum Engine Engine Oil and Filter - Change
C9 Industrial Engines Plate Locations and Film Locations