120M, 12M, 140M, 160M, 140, 150 and 160 Motor Graders Articulated Hitch Caterpillar


Articulated Hitch
`
120M, 12M, 140M, 160M, 140, 150 and 160 Motor Graders [RENR9083]
FRAME AND BODY
HITCH GP
120M, 12M, 140M, 160M, 140, 150 and 160 Motor Graders Articulated Hitch


Illustration 1g03600996

Table 1
Specification for 232-2678 Articulating Hitch Gp 
Item  Qty  Part  Specification Description 
4K-7463 Lip Type Seal  Lubricate lightly with lubricant that is being sealed. 
252-0990 Bushing  Bore before assembly is 76.403 ± 0.013 mm (3.0080 ± 0.0005 inch)
4K-8734 Bearing  Bore before assembly is 76.340 ± 0.013 mm (3.0055 ± 0.0005 inch)
319-6698 Bolt  Torque to 47 ± 7 N·m (35 ± 5 lb ft)
5K-0983 Lip Type Seal  Lubricate lightly with lubricant that is being sealed. 
5K-0988 Shim Pack  As required, use following shim pack in order to obtain proper end play:
1. Total thickness of shim pack is 2.03 ± 0.08 mm (0.080 ± 0.003 inch).
2. Thickness of four shims is 0.25 mm (0.010 inch).
3. Thickness of four shims is 0.13 mm (0.005 inch).
4. Thickness of ten shims is 0.05 mm (0.002 inch).
5. Inside diameter is 140.5 mm (5.53 inch).
6. Outside diameter is 203.2 mm (8.00 inch)
4K-7464 Shim Pack  As required, use following shim pack in order to obtain proper end play:
1. Total thickness of shim pack is 2.54 ± 0.08 mm (0.100 ± 0.003 inch).
2. Thickness of eight shims is 0.15 mm (0.006 inch).
3. Thickness of one shims is 0.81 mm (0.032 inch).
4. Thickness of ten shims is 0.05 mm (0.002 inch).
5. Inside diameter is 100.1 mm (3.94 inch).
6. Outside diameter is 155.5 mm (6.12 inch)
8T-7338 Bolt  Before assembly, apply blue Loctite 243 to the threads.
Torque to 240 ± 40 N·m (177 ± 30 lb ft)
259-2627 Bolt  Torque to 105 ± 20 N·m (77 ± 15 lb ft)

Information System:

3126B Engine for Caterpillar Built Machines Engine Oil Pan
3508B, 3512B and 3516B Generator Set Engines Alternator - Remove and Install - Alternator and Mounting Group
C32 Marine Auxiliary Engine Diagnostic Flash Code Retrieval
3512B Petroleum Engine Specifications
C9.3 Marine Auxiliary Engines Zinc Rods - Inspect/Replace
C11 and C15 Engines for Caterpillar Built Machines E360 Low Engine Oil Pressure
C6.6 Marine Generator Set Aftercooler Condensate Drain Valve - Inspect/Clean
3512B Petroleum Engine Refill Capacities and Recommendations
3512B Petroleum Engine Plate Locations and Film Locations
C9 Urban Transit Bus Engine Water Temperature Regulator - Remove and Install
Authorized Classic Machine Models {1000, 7000}
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0096 - FMI 04
Installation of a Jacket Water Heater on 3412 Generator Sets{1383}
C11 and C13 Engines for Caterpillar Built Machines E059 Low Engine Coolant Level Warning
C27 and C32 Industrial and Petroleum Engines E360 Low Engine Oil Pressure
C27 and C32 Engines for Caterpillar Built Machines E361 High Engine Coolant Temperature
2005/04/18 An Improved Rear Gear Group is Available for Reverse Engine Rotation {1204, 1206}
C27 and C32 Industrial and Petroleum Engines E539 High Intake Manifold Air Temperature
3500B High Displacement Generator Set Engines Programmable System Parameters
3412E Petroleum Engine ECM/Personality Module - Test
12M and 140 Motor Grader Shipping the Machine
3500 Petroleum Engines and Petroleum Generator Sets Specifications
C11 and C13 Engines Engine Oil Level Switch - If Equipped
3516C HD Petroleum Well Service Engine Reference Material