120M, 12M, 140M, 160M, 140, 150 and 160 Motor Graders Drawbar Caterpillar


Drawbar
`
120M, 12M, 140M, 160M, 140, 150 and 160 Motor Graders [RENR9083]
FRAME AND BODY
DRAWBAR GP
120M, 12M, 140M, 160M, 140, 150 and 160 Motor Graders Drawbar


Illustration 1g06533131

Table 1
Item  Qty  Part  Specification Description 
147-5112 Bolt  Torque to 900 ± 50 N·m (664 ± 37 lb ft)
286-0742 Nut  Torque to 520 ± 70 N·m (384 ± 52 lb ft)
As required, use the following shims to obtain end play of 0.60 ± 0.20 mm (0.024 ± 0.008 inch) at face (4): 
4 261-4674 Shim  Thickness of one shim is 0.8 mm (0.03 inch)
1 261-4676 Shim  Thickness of one shim is 0.12 mm (0.005 inch)
6 261-4675 Shim  Thickness of one shim is 0.25 mm (0.010 inch)
5P-8291 Bolt  Torque to 500 ± 65 N·m (369 ± 48 lb ft)
As required, use the following shims to obtain a maximum clearance of (D1) 0.5 mm (0.02 inch) at the smallest gap at each strip shown in Illustration 1: 
12 302-6335 Shim  Thickness of one shim is 0.25 mm (0.010 inch)
42 302-6336 Shim  Thickness of one shim is 0.5 mm (0.02 inch)
12  1D-5119 Nut  Torque to 200 ± 30 N·m (148 ± 22 lb ft)
18  201-8034 Bolt  Torque to 530 ± 70 N·m (391 ± 52 lb ft)

Information System:

C9 Urban Transit Bus Engine Air Compressor - Remove and Install
3500 Petroleum Engines and Petroleum Generator Sets Control Panel
2005/01/31 Improved Lifters are Now Used {1102, 1121, 1123}
C9 Urban Transit Bus Engine Idler Pulley - Remove and Install
3516C HD Petroleum Well Service Engine Reference Material
C11 and C13 Engines Engine Oil Level Switch - If Equipped
3500 Petroleum Engines and Petroleum Generator Sets Specifications
12M and 140 Motor Grader Shipping the Machine
3412E Petroleum Engine ECM/Personality Module - Test
3500B High Displacement Generator Set Engines Programmable System Parameters
C27 and C32 Industrial and Petroleum Engines E539 High Intake Manifold Air Temperature
2005/04/18 An Improved Rear Gear Group is Available for Reverse Engine Rotation {1204, 1206}
2005/02/21 Information Release Memo, PELJ0481 , "Product Line Expansion for Caterpillar Low and Medium Pressure Hose and Coupling Products" {5057}
Reuse and Salvage for Cast Iron Cylinder Blocks {0679, 1201, 1201}
Electronic Installation Guide{1000}
120M, 12M, 140M, 160M, 140, 150 and 160 Motor Graders Governor (Air Compressor) - Test and Adjust
C1.5 GEN SET Electric Power Generation Refill Capacities and Recommendations
2005/04/25 Cover Plate, Flange are Available for Use During Flow Tests on the Main Hydraulic Pumps {0738, 5070, 5084}
DE Series Generator Set with Cat C1.1, C1.5, and C2.2 Engines Generator Lead Connections
3508C, 3512C and 3516C Marine Engines Auxiliary Water Pump - Remove
Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736}
3500 Engines Auxiliary Water Pump - Disassemble
3500 Engines Auxiliary Water Pump - Assemble
3508B, 3512B and 3516B Generator Set Engines Exhaust Elbow - Remove and Install