C4.4 Engines for Caterpillar Built Machines Gear Group (Front) Caterpillar


Gear Group (Front)
`
C4.4 Engines for Caterpillar Built Machines [UENR4523]
BASIC ENGINE
GEAR GP
C4.4 Engines for Caterpillar Built Machines Gear Group (Front)


Illustration 1g01335907
Gear train

(1) Fuel injection pump drive gear

Tighten the nut to the following torque. ... 160 N·m (118 lb ft)
Number of teeth ... 68

(2) Camshaft gear

Torque for the 8.8 graded bolt for the camshaft gear ... 95 N·m (70 lb ft)
Torque for the 10.9 graded bolt for the camshaft gear ... 120 N·m (89 lb ft)
Number of teeth ... 68

(3) Idler gear and hub

Tighten the bolts for the idler gear to the following torque. ... 44 N·m (33 lb ft)
Width of idler gear and split bearing assembly ... 30.165 to 30.135 mm (1.1876 to 1.1864 inch)
Inside diameter of idler gear bearings with flanges ... 50.797 to 50.818 mm (1.9999 to 2.0007 inch)
Outside diameter of idler gear hub ... 50.716 to 50.737 mm (1.9967 to 1.9975 inch)
Clearance of idler gear bearing on hub ... 0.06 to 0.102 mm (0.0024 to 0.0040 inch)
Idler gear end play ... 0.10 to 0.205 mm (0.0039 to 0.0081 inch)
Maximum permissible end play ... 0.38 mm (0.015 inch)
Idler gear end play with roller bearings ... 0.24 to 0.954 mm (0.0094 to 0.0376 inch)
Number of teeth ... 73


Illustration 2g00996214
The gear train for the oil pump

(4) Crankshaft gear

Bore diameter of crankshaft gear ... 51.00 to 51.03 mm (2.0079 to 2.0091 inch)
Outside diameter of crankshaft hub ... 51.021 to 51.002 mm (2.0087 to 2.0079 inch)
Clearance of gear on crankshaft ... −0.021 to +0.028 mm (−0.0008 to 0.0011 inch)
Number of teeth ... 34

(5) Oil pump idler gear

Inside diameter of oil pump idler gear bearing ... 16.012 to 16.038 mm (0.6304 to 0.6314 inch)
Outside diameter of oil pump idler gear shaft ... 15.966 to 15.984 mm (0.6286 to 0.6293 inch)
Clearance of oil pump idler gear bearing on shaft ... 0.028 to 0.072 mm (0.0011 to 0.0028 inch)
End play of the oil pump idler gear ... 0.050 to 0.275 mm (0.0019 to 0.0108 inch)

(6) Oil pump gear

The number of teeth on the oil pump gear ... 17

Backlash values

Backlash between the idler gear (5) and the oil pump drive gear (6) ... 0.05 to 0.14 mm (0.0020 to 0.0055 inch)
Backlash between the oil pump idler gear (5) and the crankshaft gear (4) ... 0.8 to 0.23 mm (0.0315 to 0.0091 inch)
Backlash between the idler gear (3) and the crankshaft gear (4) ... 0.05 to 0.015 mm (0.0020 to 0.0006 inch)
Backlash between the camshaft gear (2) and the idler gear (3) ... 0.05 to 0.15 mm (0.0020 to 0.0059 inch)
Backlash between the fuel injection pump gear (1) and the idler gear (3) ... 0.05 to 0.15 mm (0.0020 to 0.0059 inch)
Backlash between the water pump gear (not shown) and the fuel injection pump gear (1) ... 0.05 to 0.15 mm (0.0020 to 0.0059 inch)
Backlash between the power take-off drive (if equipped) and the idler gear (3) ... 0.05 to 0.250 mm (0.0020 to 0.0098 inch)

Information System:

C13, C15, and C18 Tier 4 Final Engines Gear Group (Rear)
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing
C13, C15, and C18 Tier 4 Final Engines Crankshaft
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector Mechanism
C13, C15, and C18 Tier 4 Final Engines Water Pump
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector Mechanism
434-6509 Water Ferrule Pressure Tool{0374, 0599, 0701, 0703, 1100}
14L Motor Grader Machine Systems Fan and Fan Guard - Remove and Install
C15 and C18 On-Highway Engines Diesel Particulate Filter - Remove and Install - Clean Emissions Module
16M Series 3, 16, 18M Series 3 and 18 Motor Grader Oil Filter (Hydraulic Return)
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
C13, C15, and C18 Tier 4 Final Engines Turbocharger
G3600 A4 Engines Spark Plug Life Is Short
C13, C15, and C18 Tier 4 Final Engines Gear Group (Front)
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Solenoid Return - Test
C4.4 and C7.1 Engines Fuel Pressure Problem
14L Motor Grader Battery - Remove and Install
C4.4 Engines for Caterpillar Built Machines Fuel Injection Pump
C4.4 Engines for Caterpillar Built Machines Turbocharger
14L Motor Grader Diesel Particulate Filter - Remove and Install
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Solenoid Valve (Switch Controlled) - Test
C15 and C18 On-Highway Engines Catalyst - Remove and Install
C15 and C18 On-Highway Engines Inlet and Exhaust Valve Springs - Remove and Install
C15 and C18 On-Highway Engines Inlet and Exhaust Valves - Remove and Install