C15 and C18 Engines for Caterpillar Built Machines Gear Group (Rear) Caterpillar


Gear Group (Rear)
`


Illustration 1g03514296
Rear view

Table 1
Specification for 350-6700 Rear Gear Gp 
Item  Qty  Part  Specification Description 
229-1476 Adapter As  Lubricate the gear journals, bearing bores and thrust faces with engine oil.
Outside diameter of the 209-8624 Bushing is 77.185 ± 0.020 mm (3.0388 ± 0.0008 inch).
Thickness of the bushing is 2.480 ± 0.015 mm (0.0976 ± 0.0006 inch).
Installation depth is 4.0 ± 0.5 mm (0.16 ± 0.02 inch)
6V-5141 O-Ring Seal  Lubricate the bore lightly with the fluid that is being sealed. 
230-4069 Gear As  Assemble the gear assembly in the engine so that the end with the oil passage plug is in the hydraulic pump adapter assembly as shown in Illustration 1.
Lubricate the gear journals, bearing bores and thrust faces with engine oil. 
229-1472 Gear As  Assemble the gear assembly in the engine so that the end with the oil passage plug is in the hydraulic pump adapter assembly as shown in Illustration 1.
Lubricate the gear journals, bearing bores and thrust faces with engine oil. 
209-9770 Retainer As  Lubricate the gear journals, bearing bores and thrust faces with engine oil. 
207-8211 Idler Gear As  Lubricate the gear journals, bearing bores and thrust faces with engine oil.
Bore of the 209-8621 Bearing(1) after installation is 88.090 ± 0.013 mm (3.46810 ± 0.0005 inch)
(1) Bearing not to be serviced separately.

Information System:

C15 and C18 Engines for Caterpillar Built Machines Valve Rocker Arm
C15 and C18 On-Highway Engines Precooler - Remove and Install
C175-16 Engine Fuel Flow Is High
C15 and C18 On-Highway Engines Water Pump - Remove and Install
C15 and C18 On-Highway Engines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C15 and C18 On-Highway Engines Inlet and Exhaust Valve Guides - Remove and Install
C15 and C18 On-Highway Engines Inlet and Exhaust Valves - Remove and Install
C15 and C18 On-Highway Engines Inlet and Exhaust Valve Springs - Remove and Install
C15 and C18 On-Highway Engines Catalyst - Remove and Install
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Solenoid Valve (Switch Controlled) - Test
14L Motor Grader Diesel Particulate Filter - Remove and Install
C4.4 Engines for Caterpillar Built Machines Turbocharger
C6.6 Industrial Engine Exhaust Gas Valve (NRS) - Remove and Install
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Solenoid Valve - Test
C15 and C18 On-Highway Engines Combustion Head - Remove and Install
C280-08 Marine Engine Engine Power Ratings
C9 Petroleum Engine Product Description
C15 and C18 On-Highway Engines Air Inlet Elbow - Remove and Install
CX31-P600 Petroleum Transmission General Information
CX31-P600 Petroleum Transmission Transmission Planetary
C280-12 Marine Engine Engine Power Ratings
Installation Procedure For The New Throttle Body Cooling Lines On Certain G3500 Engines{1380}
C280-08 Marine Engine After Stopping Engine
C15 and C18 On-Highway Engines Engine Oil Cooler - Remove and Install - C18