C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install Caterpillar


Engine Oil Cooler - Remove and Install
`
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines [RENR2424]
COOLING SYSTEM
COOLER GP
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.


  1. Drain the coolant from the cooling system into a suitable container. Drain the engine oil into a suitable container. Refer to the Operation and Maintenance Manual for the procedure on draining the coolant and the engine oil.


    Illustration 1g01113679

  2. By using a suitable strap wrench, remove the oil filter element (5) from the oil cooler body (3). Discard the oil filter element in a suitable manner.

  3. Remove the hose clamps (2) and the hoses (1) from the coolant inlet and the coolant outlet on the oil cooler body (3). Note the positions of the coolant inlet and the coolant outlet for installation.

  4. Remove the adapter (4) from the oil cooler body (3). Remove the oil cooler body (3) from the cylinder block (7).

  5. Remove the O-ring (6) from the oil cooler body (3). Discard the O-ring.

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


  1. Clean the mating surfaces of the oil cooler base on the cylinder block (7) and clean the oil cooler body (3).

  2. Install a new O-ring (6) to the oil cooler body (3). Install the oil cooler body (3) to the cylinder block (7).

  3. Install the adapter (4) through the oil cooler body (3) to the cylinder block (7). Tighten the adapter (4) to a torque of 34 N·m (25 lb ft).

  4. Install the appropriate hoses (1) to the coolant inlet and the coolant outlet on the oil cooler body (3). Tighten the hose clamps (2).

  5. Lubricate the O-ring of the oil filter element (5) with clean engine oil. Install the new oil filter element to the oil cooler body (4). Tighten the oil filter element by hand. Do not use a strap wrench to tighten the oil filter element.

  6. Fill the cooling system with coolant. Fill the lubrication system with engine oil. Refer to the Operation and Maintenance Manual, "Refill Capacities" for the cooling system capacity and for the lubrication system capacity of the engine.

Information System:

C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Turbocharger - Remove and Install
C9 Marine Generator Set Plate Locations and Film Locations
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Install
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Remove
3500B Marine Propulsion Engines Refill Capacities and Recommendations
345C Excavator Machine System Specifications Hydraulic Tank and Filter
2004/12/01 A New Aftercooler Cover is Now Used {1063, 1063}
345C Excavator Machine System Specifications Relief Valve (Main)
345 MHPUC Mobile Hydraulic Power Unit Machine System Specifications Relief Valve (Main) - Heavy Lift
C32 Marine Engines Sensors and Electrical Connectors
3508C, 3512C and 3516C Marine Engines Crankshaft Main Bearings - Remove
3508C, 3512C and 3516C Marine Engines Crankshaft Main Bearings - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Assemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Disassemble
C9 Engines for Caterpillar Built Machines Basic Engine
12M, 140, 140M and 160M Motor Graders Braking and Hydraulic Fan System Brake and Hydraulic Fan System
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Flash Programming
C32 Marine Engines System Configuration Parameters
C9 Marine Generator Set Product Lifting
C7 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install
345C Excavator Machine System Specifications Final Drive
345C Excavator Machine System Specifications Boom
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Disassemble
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Assemble