C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Assemble Caterpillar


Housing (Front) - Assemble
`
1.1. Assembly Procedure
2.2. Installation of the Throttle Control
3.2. Installation of the linkage for the Fuel Injection Pump
4.2. Installation of the Stop Control
5.2. Installation of the PTO Cover

Assembly Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description 
9S-3263  Thread Lock Compound 

Note: If the engine front housing is replaced, ensure that a new emissions label is installed.

Installation of the Throttle Control



    Illustration 1g01114382
    Typical example

  1. Install the O-ring (6) to the shaft of the lever (7).

  2. Lubricate the O-ring (6) and the shaft of the lever (7) with clean engine oil. Install the lever (7) into the front housing (8).

  3. Install the C-clip (5) onto the shaft of the lever (7).

  4. Install the arm for the throttle control (3) onto the lever (7). Tighten the nut (1) and bolt (4) to a torque of 9 N·m (7 lb ft).

Installation of the linkage for the Fuel Injection Pump

  1. If necessary, perform the following procedure to install the angleich unit (15) to the lever assembly (11).


      Illustration 2g01114377

    1. Apply 9S-3263 Thread Lock Compond to the first two threads of the angleich unit (18).

    2. Install the angleich unit (18) to the lever assembly (11). Tighten the angleich unit to a torque of 5 N·m (44 lb in).

      Note: Ensure that no 9S-3263 Thread Lock Compond is allowed to contaminate the plunger assembly of the angleich unit. Contamination of the plunger assembly will render the angleich unit inoperative.

    ------ WARNING! ------

    Personal injury can result from being struck by parts propelled by a released spring force.

    Make sure to wear all necessary protective equipment.

    Follow the recommended procedure and use all recommended tooling to release the spring force.




    Illustration 3g01114562
    Typical example

  2. Install the spring (10) to the lever assembly (11).

  3. Install the O-ring (13) to the shaft (12). Lubricate the shaft with clean oil.

  4. Position the lever assembly (11) in the front housing (8). Install the shaft (12) to outside of the front housing (8).

    Note: Ensure that the groove for the C-clip (16) in the shaft (12) is positioned between the boss (15) on the front housing and the cast retainer (17) on the front housing (8).

  5. Install the C-clip (14) to the shaft (12).


    Illustration 4g01114380
    Typical example

  6. Attach the spring (10) to the notch on the inside of the front housing (8).

  7. Install the spring (9) to the lever assembly (11).

  8. Attach the spring (9) to the lever (7).

Installation of the Stop Control



    Illustration 5g01114606
    Typical example

  1. Install the C-clip (26) and install the O-ring (25) to the arm (27).

  2. Lubricate the O-ring (25) and the shaft of the arm (27) with clean oil. Install the arm assembly (27) to the front housing.

  3. Place the spring (24) and the washer (23) onto the arm (27). Install the nut (22) onto the arm (27).

  4. Install the lever (21) onto the arm (27).

  5. Install the washer (20) and the nut (19) onto the arm (27). Tighten the nuts (19) and (22) to a torque of 10 N·m (7 lb ft).

Installation of the PTO Cover



Illustration 6g01114607
Typical example

Note: The O-ring (32) and the plate (33) are not installed on the C0.5 and C0.7 engines.

  1. For C1.1/3011C, C1.5/3013C, C1.6, C2.2/3024C and C2.2/3024CT engines, install the O-ring (32) to the groove in the front housing (31).

  2. Install a new joint (30) to the rear of the front housing.

  3. For C1.1/3011C, C1.5/3013C, C1.6, C2.2/3024C and C2.2/3024CT engines, install the plates (29) and (33).

    For C0.5 and C0.7 engines, install the plate (29).

  4. Install the nuts (28) and the bolts (34) for the PTO cover. Tighten the nuts to a torque of 13 N·m (10 lb ft).

End By:

  1. Install the front housing to the engine. Refer to Disassembly and Assembly, "Housing (Front) Install" for more information.

  2. Check the maximum engine speed at no load. Refer to Testing and Adjusting, "Engine Speed - Check" for more information.

Information System:

C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Turbocharger - Remove and Install
C9 Marine Generator Set Plate Locations and Film Locations
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Install
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Remove
3500B Marine Propulsion Engines Refill Capacities and Recommendations
345C Excavator Machine System Specifications Hydraulic Tank and Filter
2004/12/01 A New Aftercooler Cover is Now Used {1063, 1063}
345C Excavator Machine System Specifications Relief Valve (Main)
345 MHPUC Mobile Hydraulic Power Unit Machine System Specifications Relief Valve (Main) - Heavy Lift
C32 Marine Engines Sensors and Electrical Connectors
3508C, 3512C and 3516C Marine Engines Crankshaft Main Bearings - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Disassemble
C9 Engines for Caterpillar Built Machines Basic Engine
12M, 140, 140M and 160M Motor Graders Braking and Hydraulic Fan System Brake and Hydraulic Fan System
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Flash Programming
C32 Marine Engines System Configuration Parameters
C9 Marine Generator Set Product Lifting
C7 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install
345C Excavator Machine System Specifications Final Drive
345C Excavator Machine System Specifications Boom
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Disassemble
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Assemble
3508C, 3512C and 3516C Marine Engines Flywheel - Remove and Install