C7 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install Caterpillar


Connecting Rod Bearings - Install
`
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     4C-5593     Anti-Seize Compound     -    


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.





Illustration 1g01126410

    Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.

  1. Install a new lower half of connecting rod bearing (4) in connecting rod bearing cap (2) .

  1. Install a new upper half of connecting rod bearing (4) in connecting rod (3) .

  1. Pull connecting rod (3) onto the crankshaft.

  1. Lubricate the new connecting rod bolts with Tooling (A) .

  1. Install connecting rod bearing cap (2) and bolts (1) . Ensure that the number on the side of connecting rod bearing cap (2) is on the same side as the number on connecting rod (3) .

  1. Tighten bolts (1) to a torque of 70 ± 5 N·m (52 ± 4 lb ft).

  1. Place an index mark on each bolt. Tighten each bolt (1) for an additional 120 ± 5 degrees (1/3 turn).

End By: Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".

Information System:

C9 Marine Generator Set Product Lifting
C32 Marine Engines System Configuration Parameters
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Flash Programming
12M, 140, 140M and 160M Motor Graders Braking and Hydraulic Fan System Brake and Hydraulic Fan System
C9 Engines for Caterpillar Built Machines Basic Engine
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Disassemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Assemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Turbocharger - Remove and Install
C9 Marine Generator Set Plate Locations and Film Locations
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Install
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Remove
345C Excavator Machine System Specifications Final Drive
345C Excavator Machine System Specifications Boom
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Disassemble
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Assemble
3508C, 3512C and 3516C Marine Engines Flywheel - Remove and Install
3126B Petroleum Engine Diagnostic Code Cross Reference
12M, 140, 140M, 150, 160M and 160 Motor Graders Hydraulic and Steering System Calibration Procedures
3508B, 3512B and 3516B Generator Set Engines Flywheel Housing - Remove
3508B, 3512B and 3516B Generator Set Engines Flywheel Housing - Install
2004/12/01 New Lockwasher Will Improve Varistor Reliability {4466}
C4.4 Industrial Engine Electrical System
C11 and C13 Engines for Caterpillar Built Machines General Information