3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Disassemble Caterpillar


Accessory Drive (Front) - Disassemble
`
1.1. Disassembly Procedure

Disassembly Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
1P-0520  Driver Group 

Start By:

  1. Remove the accessory drive (front). Refer to Disassembly and Assembly, "Accessory Drive (Front) - Remove".


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01126654

  1. Remove O-ring seal (2) and O-ring seal (4) from adapter assembly (1).

  2. Use Tooling (A) and a suitable press to remove sleeve bearing (3).

  3. If necessary, remove pipe plug (5).


    Illustration 2g01126667

  4. Remove O-ring seal (13) and O-ring seal (6) from adapter assembly (12).

  5. Remove bolts (10). Remove gear (9) from shaft (15).

  6. Remove bolts (8) and thrust washer (7).

  7. Remove shaft (15) from adapter assembly (12).

  8. Use Tooling (A) and a suitable press to remove sleeve bearing (14) from adapter assembly (12).

  9. If necessary, remove pipe plug (11).

Information System:

345C Excavator Machine System Specifications Boom
345C Excavator Machine System Specifications Final Drive
C7 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install
C9 Marine Generator Set Product Lifting
C32 Marine Engines System Configuration Parameters
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Flash Programming
12M, 140, 140M and 160M Motor Graders Braking and Hydraulic Fan System Brake and Hydraulic Fan System
C9 Engines for Caterpillar Built Machines Basic Engine
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Disassemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Assemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Turbocharger - Remove and Install
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Assemble
3508C, 3512C and 3516C Marine Engines Flywheel - Remove and Install
3126B Petroleum Engine Diagnostic Code Cross Reference
12M, 140, 140M, 150, 160M and 160 Motor Graders Hydraulic and Steering System Calibration Procedures
3508B, 3512B and 3516B Generator Set Engines Flywheel Housing - Remove
3508B, 3512B and 3516B Generator Set Engines Flywheel Housing - Install
2004/12/01 New Lockwasher Will Improve Varistor Reliability {4466}
C4.4 Industrial Engine Electrical System
C11 and C13 Engines for Caterpillar Built Machines General Information
C11 and C13 Engines for Caterpillar Built Machines Lubrication System
G3520C and G3520E Generator Set Engines Fuel Control Valve - Remove and Install
3126B Petroleum Engine Injection Actuation Pressure - Test