3508C, 3512C and 3516C Marine Engines Piston Cooling Jets - Remove and Install Caterpillar


Piston Cooling Jets - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Start By:

  1. Remove the engine oil pump, if necessary. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01127415

  1. Remove cylinder block side cover (1).


    Illustration 2g01127419

  2. Remove bolts (2) and retainer (3).

  3. Remove piston cooling jet (4) from the inside of the cylinder block.

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 3g01127419

  1. Position piston cooling jet (4) in the cylinder block. Ensure that the oil holes in the end of the piston cooling jet are facing toward the piston.

  2. Install retainer (3) and bolts (2).


    Illustration 4g01127415

  3. Install cylinder block side cover (1).

End By:

  1. Install the engine oil pump, if necessary. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".

Information System:

C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
2004/12/01 Lifting Brackets and Hardware are Available {1122}
Installation of 262-6141 Alarm Gp {7406}
345C Excavator Machine System Specifications Stick - 3.0 m (9.84 ft)
345C Excavator Machine System Specifications Stick
345C Excavator Machine System Specifications Stick
3500 and 3500B Engines Reference Numbers
3126B Petroleum Engine Injection Actuation Pressure - Test
G3520C and G3520E Generator Set Engines Fuel Control Valve - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Lubrication System
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
345C Excavator Machine System Specifications Stick - 3.4 m (11.16 ft)
3408C and 3412C Marine Auxiliary and Marine Generator Set Engines Refill Capacities and Recommendations
C32 Marine Engines Diagnostic Code Cross Reference
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install