C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install Caterpillar


Exhaust Manifold - Remove and Install
`
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines [RENR2424]
AIR INLET AND EXHAUST SYSTEM
EXHAUST GP
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


Note: The two cylinder, the three cylinder and the four cylinder engines have different exhaust manifolds. The removal procedure is similar for all models.



    Illustration 1g00825291
    Typical example

  1. Loosen the nuts (5) and the setscrews (6).

    Note: In order to prevent distortion of the exhaust manifold, loosen the outer fasteners first.

  2. Remove the nuts (5) and the setscrews (6).

    Note: Identify setscrews of different lengths so that the setscrews can be reinstalled in the correct positions.

  3. Remove the exhaust manifold (4) from the cylinder head (1).

  4. Remove the gasket (3) from the cylinder head.

  5. Remove any remaining gasket material and carbon from the cylinder head and the exhaust manifold. Be careful not to damage the mating surface on the cylinder head or the mating surface on the exhaust manifold.

  6. If necessary, remove the exhaust manifold studs (2) from the cylinder head (1).

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


Note: The two cylinder, the three cylinder and the four cylinder engines have different exhaust manifolds. The installation procedure is similar for all models.



Illustration 2g00825291
Typical example

  1. If necessary, install the exhaust manifold studs (2) to cylinder head (1).

  2. Install a new exhaust manifold gasket (3) to the cylinder head (1).

    Note: Do not use any sealant on the exhaust manifold gasket.

  3. Put the exhaust manifold (4) in position on the cylinder head (1).

  4. Install the nuts (5) and the setscrews (6).

    Note: Ensure that setscrews with different lengths are installed in the correct holes.

  5. For C0.5, C0.7, C1.1/3011C, C1.5/3013C and C1.6 engines, tighten the nuts (5) and the setscrews (6) to a torque of 10 N·m (89 lb in).

    For C2.2/3024C, and C2.2/3024CT engines, tighten the nuts (5) and the setscrews (6) to a torque of 25 N·m (18 lb ft).

    Note: On three cylinder engines, tighten the two inner setscrews first. On four cylinder engines, tighten the four inner setscrews first. Then tighten the two outer setscrews and the two nuts.

Information System:

C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C32 Marine Engines Diagnostic Code Cross Reference
3408C and 3412C Marine Auxiliary and Marine Generator Set Engines Refill Capacities and Recommendations
345C Excavator Machine System Specifications Stick - 3.4 m (11.16 ft)
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3508C, 3512C and 3516C Marine Engines Piston Cooling Jets - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove