C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Install Caterpillar


Camshaft - Install
`
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines [RENR2424]
BASIC ENGINE
CAMSHAFT GP
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Install
1.1. Installation Procedure

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


  1. Make sure that the camshaft is clean. Lubricate the camshaft with clean engine oil.


    Illustration 1g01129587
    Typical example

  2. Carefully install camshaft assembly (10) into the engine cylinder block (11). Be careful not to damage the lobes of the camshaft or the camshaft bearings.


    Illustration 2g00828468
    Typical example

  3. Install camshaft retainer (9).

    Note: The two cylinder and the three cylinder engines have a different camshaft retainer (9) and different fasteners (6) and (7), to the four cylinder engines. The removal procedure is similar for all models.

  4. Align the holes in camshaft retainer (9) with the holes in cylinder block (10).

    For C0.5, C0.7, C1.1/3011C, C1.5/3013C and C1.6 engines, install the outer setscrew (6) and install the allen head screw (7).

    For C2.2/3024C and C2.2/3024CT engines, install the setscrews (6) and (7).

    Torque both fasteners to 11 N·m (8 lb ft).



    Illustration 3g00828467
    Typical example

  5. When you install the idler gear, make sure that timing marks (2) are aligned on the following components:

    • Crankshaft gear (3)

    • Camshaft gear (4)

    • Idler gear (5)

  6. Install idler gear (5). Refer to Disassembly and Assembly, "Engine Oil Pump - Install".

  7. Install slider (1) to camshaft (4).

    Note: Make sure that the notch on the base of slider (1) is engaged on the pin of camshaft gear (4).

End By:

  1. Install the engine front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".

  2. Install the fuel priming pump. Refer to Disassembly and Assembly, "Fuel Priming Pump - Install".

  3. Install the lifters. Refer to Disassembly and Assembly, "Lifter Group- Remove and Install".

Information System:

C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C32 Marine Engines Diagnostic Code Cross Reference
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install
345C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
2005/08/01 New Clamp, New O-Ring Seal, and New Tube Assemblies for the Fuel Injection Lines {1252}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Install
C7 Engines for Caterpillar Built Machines General Information
C7 Engines for Caterpillar Built Machines Electronic Control System Components