C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove Caterpillar


Housing (Front) - Remove
`
1.1. Removal Procedure

Removal Procedure

Start By:

  1. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".
  2. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

If the front housing is not installed, do not turn the crankshaft. Damage to the engine may occur.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.





    Illustration 1g01129574

    Typical example

  1. Remove the setscrews and the nuts (5) from the front housing (4) .

  1. Turn the mechanical stop lever (3) to the full clockwise position so that the spring is held under tension.

  1. Remove the front housing (4) from the front of cylinder block (6) .

    Note: Identify the position of the locating pin (2) and the locating hole (1) for installation.

  1. Remove the joint for the front housing (not shown). Discard the joint.

  1. Inspect the front housing assembly (4) for wear or damage. If the front housing assembly is damaged, use new parts for replacement.

Information System:

C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Assemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install
345C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
2005/08/01 New Clamp, New O-Ring Seal, and New Tube Assemblies for the Fuel Injection Lines {1252}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Install
C7 Engines for Caterpillar Built Machines General Information
C7 Engines for Caterpillar Built Machines Electronic Control System Components
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install