C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install Caterpillar


Engine Oil Pan - Remove and Install
`
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines [RENR2424]
BASIC ENGINE
PAN GP-OIL
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.


Note: The two cylinder, the three cylinder and the four cylinder engines have different engine oil pans. The removal procedure is identical for all models.



    Illustration 1g00820013
    Typical example

  1. Remove the drain plugs (5) from the engine oil pan (2). Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Refill Capacities" for the approximate capacity of the lubricating oil system.

  2. Remove the sealing washers (3) from the drain plugs (5). Discard the sealing washers.

  3. Remove the setscrews (4) for the engine oil pan (2).

  4. Remove the engine oil pan (2) from the engine.

  5. Remove the joint (1). Discard the joint.

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


Note: The two cylinder, the three cylinder and the four cylinder engines have different engine oil pans. The installation procedure is identical for all models.



    Illustration 2g00820013

  1. Clean all surfaces thoroughly.

  2. Install a new joint (1) to the engine. Install the engine oil pan (2) to the engine.

  3. Install the setscrews (4) for the engine oil pan (2). Tighten the setscrews to a torque of 11 N·m (8 lb ft).

  4. Install the drain plugs (5) and new sealing washers (3) to the oil pan (2). Tighten the drain plugs to a torque of 34 N·m (25 lb ft).

  5. Fill the engine oil pan to the correct level that is indicated on the engine oil level gauge. Refer to Operation and Maintenance Manual, "Refill Capacities" for more information.

Information System:

C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install
345C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
2005/08/01 New Clamp, New O-Ring Seal, and New Tube Assemblies for the Fuel Injection Lines {1252}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Install
C7 Engines for Caterpillar Built Machines General Information
C7 Engines for Caterpillar Built Machines Electronic Control System Components
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Pilot) - Test and Adjust
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pump - Install