C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install Caterpillar


Fuel Shutoff Solenoid - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g00824952

  1. Disconnect electrical connections (3) to the fuel shutoff solenoid (1). Mark all connections for later installation.

  2. Remove fuel shutoff solenoid (1) from the fuel injection pump housing by rotating the fuel shutoff solenoid in a counterclockwise direction.

  3. Remove the O-ring (2) from fuel shutoff solenoid (1).

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 2g00824952

  1. Check the condition of O-ring seal (2). If the O-ring seal is worn or damaged use a new part for replacement.

  2. Install fuel shutoff solenoid (1) into the fuel injection pump housing by rotating the fuel shutoff solenoid in a clockwise direction. Tighten the fuel shutoff solenoid to a torque of 17 N·m (12 lb ft).

  3. Reconnect electrical connection (3) to fuel shutoff solenoid (1) before you operate the engine.

Information System:

C7 Engines for Caterpillar Built Machines Electronic Control System Components
C7 Engines for Caterpillar Built Machines General Information
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Install
2005/08/01 New Clamp, New O-Ring Seal, and New Tube Assemblies for the Fuel Injection Lines {1252}
345C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Pilot) - Test and Adjust
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating General Information
3508C, 3512C and 3516C Marine Engines Engine Speed Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Engine Speed/Timing Sensor - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
3126B Industrial Engines E027 High Inlet Air Temperature Warning