C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install Caterpillar


Engine Oil Line - Remove and Install
`
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines [RENR2424]
LUBRICATION SYSTEM
LINES GP-ENGINE OIL
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g01117696
    Typical example

  1. Loosen the nut (2) that attaches the oil line (1) to the cylinder block.

  2. Remove the banjo bolt (3) and remove the washers (4) from the cylinder block. Discard the washers (4).


    Illustration 2g01117697
    Typical example

  3. Remove the banjo bolt (3) and remove the washers (4) from the cylinder head. Discard the washers (4).

  4. Remove the oil line (1) from the engine.

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 3g01117696
    Typical example

  1. Position the oil line (1) on the engine.

  2. Position the banjo bolt (3) and the new washers (4) on the oil line (1). Install the oil line to the cylinder block.


    Illustration 4g01117697
    Typical example

  3. Position the banjo bolt (3) and the new washers (4) to the oil line (1). Install the oil line to the cylinder head.

  4. Install the nut (2) that attaches the oil line (1) to the cylinder block.

    For the C0.5, C0.7, C1.1/3011C and C1.6 engines, tighten the nut (2) to a torque of 6 N·m (4.4 lb ft).

    For the C1.5/3013C, C2.2/3024C and C2.2/3024CT engines, tighten the nut (2) to a torque of 15 N·m (11.0 lb ft).

  5. Tighten the banjo bolts (3) to 11.5 N·m (8.5 lb ft).

Information System:

C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
C7 Engines for Caterpillar Built Machines Electronic Control System Components
C7 Engines for Caterpillar Built Machines General Information
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Install
2005/08/01 New Clamp, New O-Ring Seal, and New Tube Assemblies for the Fuel Injection Lines {1252}
345C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Install
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Pilot) - Test and Adjust
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating General Information
3508C, 3512C and 3516C Marine Engines Engine Speed Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Engine Speed/Timing Sensor - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
3126B Industrial Engines E027 High Inlet Air Temperature Warning
3126B Petroleum Engine 5 Volt Engine Pressure Sensor Supply Circuit - Test