C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Install Caterpillar


Crankshaft Front Seal - Install
`
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
5P-3537  Seal Guide 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01128190
    typical example

  1. Clean housing (3) for crankshaft front seal (2) and inspect the housing for any damage.

  2. Lubricate the lip of crankshaft front seal (2) with clean engine oil.

  3. Position crankshaft front seal (2) in housing (3) for the crankshaft front seal.


    NOTICE

    Ensure that the lip of the crankshaft front seal that is spring loaded is facing toward the inside of the front housing and that it is square with the bore of the housing for the crankshaft front seal.


  4. Use Tooling (A) to install new crankshaft front seal (2).

  5. Apply clean engine oil on the area of the crankshaft pulley that will be in contact with crankshaft front seal (2).

End By:

  1. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".

Information System:

C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pump - Install
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Pilot) - Test and Adjust
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
C7 Engines for Caterpillar Built Machines Electronic Control System Components
C7 Engines for Caterpillar Built Machines General Information
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Install
2005/08/01 New Clamp, New O-Ring Seal, and New Tube Assemblies for the Fuel Injection Lines {1252}
345C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating General Information
3508C, 3512C and 3516C Marine Engines Engine Speed Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Engine Speed/Timing Sensor - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
3126B Industrial Engines E027 High Inlet Air Temperature Warning
3126B Petroleum Engine 5 Volt Engine Pressure Sensor Supply Circuit - Test
3500B High Displacement Generator Set Engines Safety Messages
3126B Petroleum Engine Engine Pressure Sensor Open or Short Circuit - Test
3126B Petroleum Engine Injector Solenoid Circuit - Test
3500 Engines Atmospheric Pressure Sensor - Remove and Install