C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Lifter Group - Remove and Install Caterpillar


Lifter Group - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
A  1U-7262  Telescoping Magnet 

Start By:

  1. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head - Remove".


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.


    Note: Mark the original location of the lifters for later installation.



    Illustration 1g00828101

  1. Use Tooling (A) to remove lifter (1) from the cylinder block.

  2. Inspect lifter (1) for wear or damage. If the lifters are worn or damaged, use new parts for replacement.

  3. Repeat Steps 1 and 2 for the remaining lifters.

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.




    Illustration 2g00692979

  1. Ensure that lifter (1) is clean and that the oil hole in the lifter is not restricted. Lubricate the lifter with clean engine oil and install the lifter in the cylinder block.

    Note: Ensure that the lifters are installed in the original location.

  2. Repeat Step 1 for the remaining lifters.

End By:

  1. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head - Install".

Information System:

C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pump - Install
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Pilot) - Test and Adjust
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
C7 Engines for Caterpillar Built Machines Electronic Control System Components
C7 Engines for Caterpillar Built Machines General Information
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Install
2005/08/01 New Clamp, New O-Ring Seal, and New Tube Assemblies for the Fuel Injection Lines {1252}
345C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating General Information
3508C, 3512C and 3516C Marine Engines Engine Speed Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Engine Speed/Timing Sensor - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
3126B Industrial Engines E027 High Inlet Air Temperature Warning
3126B Petroleum Engine 5 Volt Engine Pressure Sensor Supply Circuit - Test
3500B High Displacement Generator Set Engines Safety Messages
3126B Petroleum Engine Engine Pressure Sensor Open or Short Circuit - Test
3126B Petroleum Engine Injector Solenoid Circuit - Test
3500 Engines Atmospheric Pressure Sensor - Remove and Install
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Swing) - Test and Adjust