C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines V-Belts - Remove and Install Caterpillar


V-Belts - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g00830925

  1. Loosen bolts (1) and (3) on alternator (2).

  2. Push alternator (2) toward the engine and remove V-belt (4).

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 2g01109566
    Typical example

  1. Check the condition of the V-belt (5). If the V-belt is worn or damaged, use a new V-belt for replacement.

  2. Install the V-belt (5) in position on the engine.

  3. Slide the alternator (3) away from the engine. Tighten the setscrew (1) and setscrew (2) to a torque of 25.5 N·m (18.8 lb ft). Tighten the fasteners (4) to a torque of 25.5 N·m (18.8 lb ft) for the alternator (3). Refer to Specifications, "Belt Tension Chart" for more information on the correct belt tension.

Information System:

C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Bearing Clearance - Check
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Swing) - Test and Adjust
3500 Engines Atmospheric Pressure Sensor - Remove and Install
3126B Petroleum Engine Injector Solenoid Circuit - Test
3126B Petroleum Engine Engine Pressure Sensor Open or Short Circuit - Test
3500B High Displacement Generator Set Engines Safety Messages
3126B Petroleum Engine 5 Volt Engine Pressure Sensor Supply Circuit - Test
3126B Industrial Engines E027 High Inlet Air Temperature Warning
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator - Remove and Install
3126B Industrial Engines E100 Low Engine Oil Pressure Warning
C7 Engines for Caterpillar Built Machines Water Pump - Test
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
345 MHPUC Mobile Hydraulic Power Unit Machine System Specifications Fuel Lines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
3126B Petroleum Engine ECM/Personality Module - Test
C7 Industrial Engine Engine Monitoring System (EMS)
C9 Industrial Engines Diagnostic Flash Code Retrieval
C32 Marine Engines Analog Sensor Supply Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Refrigerant Receiver-Dryer
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Evaporator Coil