C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install Caterpillar


Electric Starting Motor - Remove and Install
`
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines [RENR2424]
ELECTRICAL AND STARTING SYSTEM
STARTING MOTOR GP
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

    Note: Disconnect all electrical connections to the electric starting motor before proceeding. Mark all connections or identify all connections for later installation.



    Illustration 1g01117494
    Typical example

  1. Remove the fasteners (1) that secure the electric starting motor (2) to the engine.

    For the C1.1/3011C, C1.5/3013C, C1.6, C2.2/3024C and C2.2/3024CT engines, the electric starter motor is secured to the engine with bolts, washers and nuts (not shown).

    For the C0.5 and C0.7 engines, the electric starter motor is secured to the engine with setscrews and washers.

  2. Remove the electric starting motor (2) from the engine.

Installation Procedure



    Illustration 2g01117494
    Typical example

  1. Install the electric starting motor (2) in position on the engine.

  2. Install the fasteners (1) that secure the electric starting motor (2) to the engine. Tighten the fasteners to a torque of 50 N·m (36.9 lb ft).

    For the C1.1/3011C, C1.5/3013C, C1.6, C2.2/3024C and C2.2/3024CT engines, the electric starter motor is secured to the engine with bolts, washers and nuts (not shown).

    For the C0.5 and C0.7 engines, the electric starter motor is secured to the engine with setscrews and washers.

    Note: Reconnect all electrical connections to the electric starting motor before you operate the engine.

Information System:

C7 Engines for Caterpillar Built Machines Water Pump - Test
3126B Industrial Engines E100 Low Engine Oil Pressure Warning
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines V-Belts - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Bearing Clearance - Check
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Relief Valve (Swing) - Test and Adjust
3500 Engines Atmospheric Pressure Sensor - Remove and Install
3126B Petroleum Engine Injector Solenoid Circuit - Test
345 MHPUC Mobile Hydraulic Power Unit Machine System Specifications Fuel Lines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
3126B Petroleum Engine ECM/Personality Module - Test
C7 Industrial Engine Engine Monitoring System (EMS)
C9 Industrial Engines Diagnostic Flash Code Retrieval
C32 Marine Engines Analog Sensor Supply Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Refrigerant Receiver-Dryer
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Evaporator Coil
3508C, 3512C and 3516C Marine Engines Turbocharger Outlet Pressure Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Coolant Temperature Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Turbocharger Inlet Pressure Sensor - Remove and Install
C7 Petroleum Engine Engine Oil and Filter - Change