3508C, 3512C and 3516C Marine Engines Turbocharger Inlet Pressure Sensor - Remove and Install Caterpillar


Turbocharger Inlet Pressure Sensor - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01129348

  1. Disconnect the harness assembly and remove turbocharger inlet pressure sensor (1).

  2. Remove the O-ring seal from the turbocharger inlet pressure sensor.

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
1U-6396  O-Ring Assembly Compound 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 2g01129348

  1. Install a new O-ring seal on turbocharger inlet pressure sensor (1). Apply Tooling (A) to the O-ring seal.

  2. Install turbocharger inlet pressure sensor (1) and tighten to a torque of 10 ± 2 N·m (89 ± 18 lb in).

  3. Connect the harness assembly.

Information System:

3508C, 3512C and 3516C Marine Engines Coolant Temperature Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Turbocharger Outlet Pressure Sensor - Remove and Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Evaporator Coil
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Refrigerant Receiver-Dryer
C32 Marine Engines Analog Sensor Supply Circuit - Test
C9 Industrial Engines Diagnostic Flash Code Retrieval
C7 Industrial Engine Engine Monitoring System (EMS)
3126B Petroleum Engine ECM/Personality Module - Test
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
345 MHPUC Mobile Hydraulic Power Unit Machine System Specifications Fuel Lines
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C7 Engines for Caterpillar Built Machines Water Pump - Test
C7 Petroleum Engine Engine Oil and Filter - Change
C9 Industrial Engines Plate Locations and Film Locations
3500B High Displacement Generator Set Engines Reference Material
345C Excavator Hydraulic System Pump Control (Output Flow) - Adjust
2004/12/01 Updated Information to Operation and Maintenance Manual, SEBU6251 , "Engine Oil (3116 and 3126 Marine Engines" {1348, 7581}
3508C, 3512C and 3516C Marine Engines Engine Oil Pressure Sensor - Remove and Install
3406C Engines for Caterpillar Built Machines Alternator and Regulator
3508C, 3512C and 3516C Marine Engines Fuel Pressure Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Crankcase Pressure Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Aftercooler Coolant Temperature Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Fuel Priming Pump - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install