3508C, 3512C and 3516C Marine Engines Crankcase Pressure Sensor - Remove and Install Caterpillar


Crankcase Pressure Sensor - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01129987

  1. Disconnect the harness assembly and remove crankcase pressure sensor (1).

  2. Remove the O-ring seal from the crankcase pressure sensor.

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 2g01129987

  1. Install a new O-ring seal on the crankcase pressure sensor (1).

  2. Install crankcase pressure sensor (1) and tighten to a torque of 10 ± 2 N·m (89 ± 18 lb in).

  3. Connect the harness assembly.

Information System:

3508C, 3512C and 3516C Marine Engines Fuel Pressure Sensor - Remove and Install
3406C Engines for Caterpillar Built Machines Alternator and Regulator
3508C, 3512C and 3516C Marine Engines Engine Oil Pressure Sensor - Remove and Install
2004/12/01 Updated Information to Operation and Maintenance Manual, SEBU6251 , "Engine Oil (3116 and 3126 Marine Engines" {1348, 7581}
345C Excavator Hydraulic System Pump Control (Output Flow) - Adjust
3500B High Displacement Generator Set Engines Reference Material
C9 Industrial Engines Plate Locations and Film Locations
C7 Petroleum Engine Engine Oil and Filter - Change
3508C, 3512C and 3516C Marine Engines Turbocharger Inlet Pressure Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Coolant Temperature Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Turbocharger Outlet Pressure Sensor - Remove and Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Evaporator Coil
3508C, 3512C and 3516C Marine Engines Aftercooler Coolant Temperature Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Fuel Priming Pump - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Coolant Temperature Switch - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
3508C, 3512C and 3516C Marine Engines Electronic Unit Injector - Remove
3508C, 3512C and 3516C Marine Engines Electronic Unit Injector - Install
C7 Engines for Caterpillar Built Machines Basic Engine
C7 Engines for Caterpillar Built Machines Fuel System
C7 Engines for Caterpillar Built Machines Air Inlet and Exhaust System
C7 Engines for Caterpillar Built Machines Cooling System
C7 Engines for Caterpillar Built Machines Lubrication System