3500 Engines Prelubrication Oil Pump - Remove and Install Caterpillar


Prelubrication Oil Pump - Remove and Install
`
3500 Engines [RENR9365]
LUBRICATION SYSTEM
PUMP GP-PRELUBRICATION
3500 Engines Prelubrication Oil Pump - Remove and Install
3500 Engines Prelubrication Oil Pump - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.



NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


  1. Disconnect the batteries.

  2. Put an index mark on the harness assemblies that are connected to the prelubrication oil pump.

  3. Disconnect the harness assemblies from the prelubrication oil pump.


    Illustration 1g01130821

  4. Disconnect tube assembly (1) and disconnect tube assembly (2) from the prelubrication oil pump.

  5. Fasten a suitable lifting device to prelubrication oil pump (3). The weight of prelubrication oil pump (3) is approximately 24 kg (53 lb).

  6. Remove bolts (4) and remove the prelubrication oil pump.

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 2g01130821

  1. Fasten a suitable lifting device to prelubrication oil pump (3). The weight of prelubrication oil pump (3) is approximately 24 kg (53 lb).

  2. Position the prelubrication oil pump and install bolts (4).

  3. Connect tube assembly (2) and tube assembly (1) to the prelubrication oil pump.

  4. Connect the harness assemblies to the prelubrication oil pump.

  5. Connect the batteries.

Information System:

3508B, 3512B and 3516B Generator Set Engines Electric Starting Motor - Remove and Install
VR6B Voltage Regulator Installation For 480V Sensing VR3 Regulators On 3500 Generator Sets {4467}
C9 Engines for Caterpillar Built Machines Aftercooler - Test
C7 Engines for Caterpillar Built Machines Lubrication System
C7 Engines for Caterpillar Built Machines Cooling System
C7 Engines for Caterpillar Built Machines Air Inlet and Exhaust System
C7 Engines for Caterpillar Built Machines Fuel System
C7 Engines for Caterpillar Built Machines Basic Engine
3508C, 3512C and 3516C Marine Engines Electronic Unit Injector - Install
3508C, 3512C and 3516C Marine Engines Electronic Unit Injector - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
G3612 and G3616 Engines Specifications
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning and Heating System Sensor Operation
C32 Marine Engines CAN Data Link Circuit - Test
G3606 and G3608 Engines Specifications
C32 Marine Engines Cat Data Link Circuit - Test
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Electrical System
C-10, C-12, C-15 and C-16 Industrial Engines Engine Speed/Timing Sensor - Calibrate
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Troubleshooting
Replacing the MIDS Display with an Advisor M2 Display{7490}
345C Excavator Leaving the Machine
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Remove
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Install