C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Install Caterpillar


Turbocharger - Install
`
C11 and C13 Engines for Caterpillar Built Machines [RENR9214]
AIR INLET AND EXHAUST SYSTEM
TURBOCHARGER GP
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Remove
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Install
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
5P-3931  Anti-Seize Compound 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01131603

  1. Apply Tooling (A) to the turbocharger mounting studs on the exhaust manifold.

  2. Position the gasket and turbocharger (2) on the engine.

    Note: Discard the nuts after use. Use new nuts for installation.

  3. Install nuts (1).

  4. Connect tube assembly (5).

  5. Connect hose assemblies (3), (4), and (6).

  6. Fill the coolant system. Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".

Information System:

C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Remove
345C Excavator Leaving the Machine
Replacing the MIDS Display with an Advisor M2 Display{7490}
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Troubleshooting
C-10, C-12, C-15 and C-16 Industrial Engines Engine Speed/Timing Sensor - Calibrate
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Electrical System
C32 Marine Engines Cat Data Link Circuit - Test
G3606 and G3608 Engines Specifications
C32 Marine Engines CAN Data Link Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning and Heating System Sensor Operation
G3612 and G3616 Engines Specifications
3500 Engines Prelubrication Oil Pump - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Remove
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Install
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Remove
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Disassemble
3500 Engines Coolant Level Sensor - Remove and Install
325D and 329D Excavators Machine Security System - If Equipped
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Assemble
C11 and C13 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes