C11 and C13 Engines for Caterpillar Built Machines Water Pump - Remove Caterpillar


Water Pump - Remove
`
1.1. Removal Procedure

Removal Procedure


    NOTICE

    Keep all parts clean from contaminants.

    Contaminants may cause rapid wear and shortened component life.



    NOTICE

    Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

    Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

    Dispose of all fluids according to local regulations and mandates.


  1. Drain the coolant system. Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".


    Illustration 1g01132004

  2. Disconnect hose assembly (1).

  3. Remove bolts (2).

  4. Remove housing (3).

  5. Remove bracket (4).

  6. Remove tube assembly (5).


    Illustration 2g01132005

  7. Remove tube assembly (6).

  8. Remove belt tensioner (7).

  9. Remove bolts (8).

  10. Remove water pump (9).

Information System:

3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Remove
C11 and C13 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Remove
345C Excavator Leaving the Machine
Replacing the MIDS Display with an Advisor M2 Display{7490}
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Troubleshooting
C-10, C-12, C-15 and C-16 Industrial Engines Engine Speed/Timing Sensor - Calibrate
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Electrical System
C32 Marine Engines Cat Data Link Circuit - Test
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Disassemble
3500 Engines Coolant Level Sensor - Remove and Install
325D and 329D Excavators Machine Security System - If Equipped
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Assemble
C11 and C13 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
345C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
2005/03/07 Wireless Communication Adapter Allows Radio Frequency Communication Between Computer and Electronic Control Module {0785, 0788}
C32 Marine Engines Coolant Level Sensor Circuit - Test