C11 and C13 Engines for Caterpillar Built Machines Water Pump - Assemble Caterpillar


Water Pump - Assemble
`
1.1. Assembly Procedure

Assembly Procedure

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
B     1P-1861     Retaining Ring Pliers     1    
D     138-9299     Seal Guide     1    
E     139-0088     Seal Installer     1    
F     169-5464     Quick Cure Primer     -    


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.





    Illustration 1g01132114



    Illustration 2g01768596

  1. Use Tooling (F) in order to clean shaft assembly (9) and the counterbore in housing assembly (7) .

  1. Use Tooling (D) in order to install oil seal (8) . Install the oil seal with the part number toward the housing assembly. Ensure that the oil seal is flush with the housing assembly. Do not lubricate the oil seal.

  1. Install inner bearing (10) onto shaft assembly (9) .

  1. Install shaft assembly (9) into housing assembly (7) .

  1. Use Tooling (B) in order to install retaining ring (11) .

  1. Use Tooling (E) and a suitable press in order to install water seal (6) onto shaft assembly (9) . Install the water seal with the part number Upward. Ensure that the water seal is flush against the housing assembly. Do not lubricate the seal.

  1. Use a suitable press in order to install impeller (5) onto shaft assembly (9) . The top of impeller (5) should be installed to Depth (X) below the surface of the housing assembly. Depth (X) is 8.40 ± 0.25 mm (0.331 ± 0.010 inch).

  1. Use a suitable press in order to install gear (12) .

  1. Install bearing (13) . Ensure that the bearing is flush with the gear.

  1. Install hex washer (14) and hex socket head bolt (15) .

  1. Install O-ring seal (2) and O-ring seal (4) in cover (3) . Install cover (3) on housing assembly (7) .

  1. Install elbow assembly (1) .

End By: Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".

Information System:

325D and 329D Excavators Machine Security System - If Equipped
3500 Engines Coolant Level Sensor - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Disassemble
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Remove
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Remove
C11 and C13 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Remove
345C Excavator Leaving the Machine
Replacing the MIDS Display with an Advisor M2 Display{7490}
C11 and C13 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
345C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
2005/03/07 Wireless Communication Adapter Allows Radio Frequency Communication Between Computer and Electronic Control Module {0785, 0788}
C32 Marine Engines Coolant Level Sensor Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Control Panel (Air Conditioner and Heater)
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
C11 and C13 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Remove - Engine Oil Pump and Water Pump