C11 and C13 Engines for Caterpillar Built Machines Flywheel - Install Caterpillar


Flywheel - Install
`
C11 and C13 Engines for Caterpillar Built Machines [RENR9214]
BASIC ENGINE
FLYWHEEL GP
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Install
1.1. Installation Procedure

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
589–7435  Link Bracket 
FT2712  Guide Stud 
Loctite 242 

    ------ WARNING! ------

    Always wear protective gloves when handling parts that have been heated.


  1. Raise the temperature of the ring gear. Position the ring gear with the part number toward the crankshaft. Install the ring gear on the flywheel. Allow the ring gear to cool. Use a soft hammer to seat the ring gear against the shoulder of the flywheel.


    Illustration 1g01132214

  2. Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2) is approximately 79 kg (175 lb).

  3. Position flywheel (2) on Tooling (B).

  4. Apply Tooling (C) to bolts (1).

  5. Install bolts (1). Remove Tooling (B). Install remaining bolt (1). Tighten the bolts evenly to a torque of 300 ± 40 N·m (221 ± 30 lb ft).

  6. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for the correct procedure.

Information System:

C11 and C13 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Assemble
325D and 329D Excavators Machine Security System - If Equipped
3500 Engines Coolant Level Sensor - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Disassemble
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Remove
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Remove
C11 and C13 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Install
C11 and C13 Engines for Caterpillar Built Machines Turbocharger - Remove
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
C11 and C13 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
345C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
2005/03/07 Wireless Communication Adapter Allows Radio Frequency Communication Between Computer and Electronic Control Module {0785, 0788}
C32 Marine Engines Coolant Level Sensor Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Control Panel (Air Conditioner and Heater)
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
C11 and C13 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Remove - Engine Oil Pump and Water Pump
3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Install - Engine Oil Pump and Water Pump
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Disassemble - Engine Oil Pump and Water Pump