C11 and C13 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install Caterpillar


Flywheel Housing - Remove and Install
`
C11 and C13 Engines for Caterpillar Built Machines [RENR9214]
BASIC ENGINE
HOUSING GP-FLYWHEEL
C11 and C13 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Start By:

  1. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".

  2. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".

  1. Support the engine.


    Illustration 1g01132273

  2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2) is approximately 62 kg (137 lb).

  3. Remove bolts (1) and flywheel housing (2).

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
1U-8846  Gasket Sealant 

  1. Apply Tooling (A) to the face of the cylinder block.


    Illustration 2g01132273

  2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2) is approximately 62 kg (137 lb). Position flywheel housing (2) on the rear of the cylinder block.

  3. Install bolts (1).

End By:

  1. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".

  2. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".

Information System:

C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Install
C11 and C13 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Assemble
325D and 329D Excavators Machine Security System - If Equipped
3500 Engines Coolant Level Sensor - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Disassemble
C11 and C13 Engines for Caterpillar Built Machines Water Pump - Remove
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove
3508B, 3512B and 3516B Generator Set Engines Housing (Front) - Remove
345C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
2005/03/07 Wireless Communication Adapter Allows Radio Frequency Communication Between Computer and Electronic Control Module {0785, 0788}
C32 Marine Engines Coolant Level Sensor Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Control Panel (Air Conditioner and Heater)
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
C11 and C13 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Remove - Engine Oil Pump and Water Pump
3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Install - Engine Oil Pump and Water Pump
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Disassemble - Engine Oil Pump and Water Pump
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Assemble - Engine Oil Pump and Water Pump
C32 Marine Engines Digital Sensor Supply Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning System Troubleshooting