3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Install - Engine Oil Pump and Water Pump Caterpillar


Accessory Drive (Front) - Install - Engine Oil Pump and Water Pump
`
1.1. Installation Procedure

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01132545

  1. Install the O-ring seal in pump adapter assembly (5). Apply clean engine oil to the bore in front housing (3) for pump adapter assembly (5).

  2. Position pump adapter assembly (5) in the front housing and install bolts (4).


    Illustration 2g01132543

  3. Install the O-ring seal in pump adapter assembly (1). Apply clean engine oil to the bore in front housing (3) for pump adapter assembly (1).

  4. Position pump adapter assembly (1) in the front housing and install bolts (2).

End By:

  1. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".

  2. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove and Install".

  3. Install the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".

Information System:

3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Remove - Engine Oil Pump and Water Pump
C11 and C13 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Control Panel (Air Conditioner and Heater)
C32 Marine Engines Coolant Level Sensor Circuit - Test
2005/03/07 Wireless Communication Adapter Allows Radio Frequency Communication Between Computer and Electronic Control Module {0785, 0788}
345C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
C11 and C13 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes
C11 and C13 Engines for Caterpillar Built Machines Flywheel - Install
C11 and C13 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Disassemble - Engine Oil Pump and Water Pump
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Assemble - Engine Oil Pump and Water Pump
C32 Marine Engines Digital Sensor Supply Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning System Troubleshooting
C32 Marine Engines Electrical Power Supply Circuit - Test
C11 and C13 Engines for Caterpillar Built Machines Cylinder Head - Remove
C11 and C13 Engines for Caterpillar Built Machines Cylinder Head - Install
C11 and C13 Engines for Caterpillar Built Machines Camshaft - Remove
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning System Troubleshooting
C11 and C13 Engines for Caterpillar Built Machines Camshaft - Install
C32 Marine Engines Engine Pressure Sensor Open or Short Circuit - Test
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Global Positioning System Interface Module