3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Assemble - Engine Oil Pump and Water Pump Caterpillar


Accessory Drive (Front) - Assemble - Engine Oil Pump and Water Pump
`
1.1. Assembly Procedure

Assembly Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
1P-0520  Driver Group 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01133092

  1. Align the oil hole in sleeve bearing (10) and the oil hole in pump adapter assembly (4). Use Tooling (A) and a suitable press to install sleeve bearing (10) into pump adapter assembly (4).

    Note: The sleeve bearing must not project above the pump adapter assembly.

  2. Apply clean engine oil to sleeve bearing (10).


    Illustration 2g01133098

  3. Position accessory drive gear (9) on pump drive shaft (7). Install bolts (8).

  4. If necessary, install socket setscrew (13) in the end of pump drive shaft and tighten to a torque of 6 ± 1 N·m (53 ± 9 lb in).


    Illustration 3g01133086

  5. Install pump adapter assembly (4) onto pump drive shaft (7).

  6. Install thrust washer (6) and bolts (5).

  7. Install O-ring seal (12) and O-ring seal (11) on pump adapter assembly (4).


    Illustration 4g01132964

  8. Align the oil hole in sleeve bearing (1) and the oil hole in pump adapter assembly (2). Use Tooling (A) and a suitable press to install sleeve bearing (1) into pump adapter assembly (2).

  9. Install O-ring seal (3) on the pump adapter assembly.

End By:

  1. Install the accessory drive for the engine oil pump and the water pump. Refer to Disassembly and Assembly, "Accessory Drive (Front) - Install".

Information System:

3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Disassemble - Engine Oil Pump and Water Pump
3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Install - Engine Oil Pump and Water Pump
3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Remove - Engine Oil Pump and Water Pump
C11 and C13 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Control Panel (Air Conditioner and Heater)
C32 Marine Engines Coolant Level Sensor Circuit - Test
2005/03/07 Wireless Communication Adapter Allows Radio Frequency Communication Between Computer and Electronic Control Module {0785, 0788}
345C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
C11 and C13 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Troubleshooting Faults With Service Codes
C32 Marine Engines Digital Sensor Supply Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning System Troubleshooting
C32 Marine Engines Electrical Power Supply Circuit - Test
C11 and C13 Engines for Caterpillar Built Machines Cylinder Head - Remove
C11 and C13 Engines for Caterpillar Built Machines Cylinder Head - Install
C11 and C13 Engines for Caterpillar Built Machines Camshaft - Remove
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning System Troubleshooting
C11 and C13 Engines for Caterpillar Built Machines Camshaft - Install
C32 Marine Engines Engine Pressure Sensor Open or Short Circuit - Test
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Global Positioning System Interface Module
3508C, 3512C and 3516C Marine Engines Inlet and Exhaust Valves - Remove and Install
3508C, 3512C and 3516C Marine Engines Inlet and Exhaust Valve Springs - Remove and Install