C11 and C13 Engines for Caterpillar Built Machines Camshaft - Remove Caterpillar


Camshaft - Remove
`
1.1. Removal Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
201-4211  Camshaft Pilot 
201-4212 Camshaft Pilot 

Start By:

  1. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".

  2. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".

  3. Remove the camshaft position sensor. Refer to Disassembly and Assembly, "Camshaft Position Sensor - Remove and Install".


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


  1. Turn the crankshaft to top center compression stroke for the No. 1 piston.

  2. Ensure that the timing marks on the following gears are aligned: the camshaft drive gear, the idler gear and the crankshaft gear.

  3. Wire the valve lifters away from the camshaft.


    Illustration 1g01133114

  4. Remove bolts (1).


    Illustration 2g01144335

  5. Install Tooling (A) on the rear of the camshaft.


    Illustration 3g01144336

    Note: Lubricate Tooling (A) with clean oil.

  6. Carefully remove camshaft (2) from the engine.

Information System:

C11 and C13 Engines for Caterpillar Built Machines Cylinder Head - Install
C11 and C13 Engines for Caterpillar Built Machines Cylinder Head - Remove
C32 Marine Engines Electrical Power Supply Circuit - Test
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning System Troubleshooting
C32 Marine Engines Digital Sensor Supply Circuit - Test
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Assemble - Engine Oil Pump and Water Pump
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Disassemble - Engine Oil Pump and Water Pump
3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Install - Engine Oil Pump and Water Pump
3508B, 3512B and 3516B Generator Set Engines Accessory Drive (Front) - Remove - Engine Oil Pump and Water Pump
C11 and C13 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
345 MHPUC Mobile Hydraulic Power Unit Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Control Panel (Air Conditioner and Heater)
307D, 311D, 312D, 313D, 315D, 318D, 319D, 320D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 340D, 345D, 349D, 374D, 390D and M325D Excavators Air Conditioning and Heating Air Conditioning System Troubleshooting
C11 and C13 Engines for Caterpillar Built Machines Camshaft - Install
C32 Marine Engines Engine Pressure Sensor Open or Short Circuit - Test
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Global Positioning System Interface Module
3508C, 3512C and 3516C Marine Engines Inlet and Exhaust Valves - Remove and Install
3508C, 3512C and 3516C Marine Engines Inlet and Exhaust Valve Springs - Remove and Install
3500 Engines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3508C, 3512C and 3516C Marine Engines Inlet and Exhaust Valve Guides - Remove and Install
C32 Marine Engines Engine Speed/Timing Sensor Circuit - Test
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Wastegate - Test
C7 and C9 Marine Engines Engine Synchronize Switch Circuit - Test
C7 Engines for Caterpillar Built Machines Fuel System Pressure - Test