C11 and C13 Engines for Caterpillar Built Machines Fan Drive Mounting Group - Remove and Install Caterpillar


Fan Drive Mounting Group - Remove and Install
`
C11 and C13 Engines for Caterpillar Built Machines [RENR9214]
BASIC ENGINE
DRIVE GP-FAN
C11 and C13 Engines for Caterpillar Built Machines Fan Drive Mounting Group - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

    ------ WARNING! ------

    Personal injury can result from contact with refrigerant.

    Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.

    Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.

    Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.

    Personal injury or death can result from inhaling refrigerant through a lit cigarette.

    Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.

    Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.

    Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.


  1. Recover the air conditioner refrigerant.

  2. Disconnect the hose assemblies from the air conditioner compressor.

  3. Disconnect the harness assemblies from the alternator.


    Illustration 1g01135160

  4. Remove bolts (1).


    Illustration 2g01135201

  5. Remove belt (2).

  6. Attach a suitable lifting device to fan drive mounting group (4). The weight of fan drive mounting group (4) is approximately 45 kg (100 lb).

  7. Remove bolts (3) and nuts (5).

  8. Remove fan drive mounting group (4).

Installation Procedure



    Illustration 3g01135201

  1. Install the idler pulley assemblies if the idler pulley assemblies were removed. Tighten the bolts for the idler pulley assemblies to a torque of 50 ± 5 N·m (37 ± 4 lb ft).

  2. Attach a suitable lifting device to fan drive mounting group (4). The weight of fan drive mounting group (4) is approximately 45 kg (100 lb). Position fan drive mounting group (4) on the engine.

  3. Install bolts (3) and nuts (5).

  4. Install belt (2).


    Illustration 4g01135160

  5. Install bolts (1).

  6. Connect the harness assemblies to the alternator.

  7. Connect the hose assemblies to the air conditioner compressor.

    ------ WARNING! ------

    Personal injury can result from contact with refrigerant.

    Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.

    Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.

    Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.

    Personal injury or death can result from inhaling refrigerant through a lit cigarette.

    Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.

    Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.

    Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.


  8. Recharge the air conditioner refrigerant.

Information System:

C32 Marine Engines Event Codes
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Remove
3508B, 3512B and 3516B Generator Set Engines Engine Oil Sequence Valves - Remove and Install
3412E Petroleum Engine Diagnostic Code Cross Reference
3412E Petroleum Engine Intermittent Engine Shutdown
C9.3 Tier 4 Final Engines Fuel Filter Base
2005/01/17 New Bearings for the Engine Oil Pump are Available {1304}
C7 Engines for Caterpillar Built Machines Cooling System - Test
3500 and 3500B Engines Aftercooler Core - Inspect/Clean
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant System - Charge
3412E Petroleum Engine Auxiliary Temperature Sensor Circuit - Test
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant System - Evacuate
3508B, 3512B and 3516B Generator Set Engines Balancer Group (Front) - Remove and Install - 3508B Engine
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant System - Flush
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant Recovery
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Required Tools
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Install
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant Compressor Oil - Check
C11 and C13 Engines for Caterpillar Built Machines Alternator - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Remove
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Install
3500B Marine Propulsion Engines Auxiliary Water Pump - Inspect
Particulate Filter for Stationary Engines in Standby Applications{1091}