3508B, 3512B and 3516B Generator Set Engines Balancer Group (Front) - Remove and Install - 3508B Engine Caterpillar


Balancer Group (Front) - Remove and Install - 3508B Engine
`
3508B, 3512B and 3516B Generator Set Engines [RENR5060]
BASIC ENGINE
BALANCER GP
3508B, 3512B and 3516B Generator Set Engines Balancer Group (Front) - Remove and Install - 3508B Engine
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
1P-0520  Driver Group 

Start By:

  1. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove and Install".


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01135236

  1. Remove bolts (3) and thrust plate (4).

  2. Remove balancer gear (5) from gear shaft (2).

  3. Use Tooling (A) and a suitable press to remove sleeve bearing (6) from balancer gear (5).

  4. Remove bolts (1) and gear shaft (2) from the front of the cylinder block.

Installation Procedure

Table 2
Required Tools 
Tool  Part Number  Part Description  Qty 
1P-0520  Driver Group 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 2g01135236

  1. Use Tooling (A) and a suitable press to install sleeve bearing (6) in balancer gear (5).

    Note: Sleeve bearing (6) must be machined to the correct inside diameter. Refer to Special Instructions, SEHS9282, "Machining of Replacement Sleeve Bearings".

  2. Install gear shaft (2) and bolts (1). Tighten bolts (1) to a torque of 140 ± 10 N·m (103 ± 7 lb ft).

  3. Apply clean engine oil on the sleeve bearing in balancer gear (5) and gear shaft (2). Install balancer gear (5) on gear shaft (2). Make sure that the marks on balancer gear (5) and the crankshaft gear are in alignment with the rotation of the engine. Install thrust plate (4) and bolts (3).

End By:

  1. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove and Install".

Information System:

C11 and C13 Engines for Caterpillar Built Machines Fan Drive Mounting Group - Remove and Install
C32 Marine Engines Event Codes
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Remove
3508B, 3512B and 3516B Generator Set Engines Engine Oil Sequence Valves - Remove and Install
3412E Petroleum Engine Diagnostic Code Cross Reference
3412E Petroleum Engine Intermittent Engine Shutdown
C9.3 Tier 4 Final Engines Fuel Filter Base
2005/01/17 New Bearings for the Engine Oil Pump are Available {1304}
C7 Engines for Caterpillar Built Machines Cooling System - Test
3500 and 3500B Engines Aftercooler Core - Inspect/Clean
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant System - Charge
3412E Petroleum Engine Auxiliary Temperature Sensor Circuit - Test
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant System - Flush
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant Recovery
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Required Tools
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Install
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant Compressor Oil - Check
C11 and C13 Engines for Caterpillar Built Machines Alternator - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Remove
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Install
3500B Marine Propulsion Engines Auxiliary Water Pump - Inspect
Particulate Filter for Stationary Engines in Standby Applications{1091}
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Fuel Filter Base - Electric Fuel Priming Pump