C11 and C13 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install Caterpillar


Electric Starting Motor - Remove and Install
`
C11 and C13 Engines for Caterpillar Built Machines [RENR9214]
ELECTRICAL AND STARTING SYSTEM
STARTING MOTOR GP
C11 and C13 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

------ WARNING! ------

Accidental engine starting can cause injury or death to personnel working on the equipment.

To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.

Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.


  1. Disconnect the batteries.

  2. Place identification marks on all of the harness assemblies that are connected to the electric starting motor and the solenoid.


    Illustration 1g01135491

  3. Disconnect the harness assemblies from solenoid (1).

  4. Fasten a suitable lifting device to electric starting motor (2). The weight of electric starting motor (2) is approximately 26 kg (57 lb).

  5. Remove bolts (3). Remove electric starting motor (2) and gasket (4).

Installation Procedure



    Illustration 2g01135491


    Illustration 3g01135493

  1. Fasten a suitable lifting device to electric starting motor (2). The weight of electric starting motor (2) is approximately 26 kg (57 lb).

  2. Position gasket (4) and electric starting motor (2) on the flywheel housing. Install bolts (3).

  3. Position the harness assembly on solenoid (1) and install nut (5). Tighten the nut to a torque of 31 ± 4 N·m (23 ± 3 lb ft).

  4. Position the harness assembly on solenoid (1) and install nut (7). Tighten the nut to a torque of 2.25 ± 0.25 N·m (20 ± 2 lb in).

  5. Position the harness assembly on solenoid (1) and install nut (6). Tighten the nut to a torque of 2.25 ± 0.25 N·m (20 ± 2 lb in).

  6. If necessary, install the connector and install nut (9) and bolt (8). Tighten the nut to a torque of 31 ± 4 N·m (23 ± 3 lb ft). Tighten the bolt to a torque of 8 ± 3 N·m (71 ± 27 lb in).

  7. Connect the batteries.

Information System:

C11 and C13 Engines for Caterpillar Built Machines Alternator - Remove and Install
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant Compressor Oil - Check
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Install
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Required Tools
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant Recovery
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant System - Flush
3508B, 3512B and 3516B Generator Set Engines Balancer Group (Front) - Remove and Install - 3508B Engine
C11 and C13 Engines for Caterpillar Built Machines Fan Drive Mounting Group - Remove and Install
C32 Marine Engines Event Codes
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Remove
3508B, 3512B and 3516B Generator Set Engines Engine Oil Sequence Valves - Remove and Install
3412E Petroleum Engine Diagnostic Code Cross Reference
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Remove
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Install
3500B Marine Propulsion Engines Auxiliary Water Pump - Inspect
Particulate Filter for Stationary Engines in Standby Applications{1091}
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Fuel Filter Base - Electric Fuel Priming Pump
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Disassemble
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Assemble
12M and 140 Motor Grader Roading the Machine
345C Excavator Machine System Specifications Boom Cylinder
C11 and C13 Engines for Caterpillar Built Machines Electronic Unit Injector - Install
3500B Marine Propulsion Engines Heat Exchanger - Inspect
2005/01/17 Correction to Engine Speed/Timing Sensor-Calibrate {1912}