3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Install Caterpillar


Engine Oil Cooler - Install
`
1.1. Installation Procedure

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01135604

  1. Attach a suitable lifting device to engine oil cooler (7). The weight of engine oil cooler (7) is approximately 78 kg (172 lb).

  2. Install the O-ring seal on tube (13). Apply clean engine oil to the O-ring seal.

  3. Position engine oil cooler (7) on tube (13). Install bolts (12).

  4. Position the gasket and adapter (11) on the engine oil cooler. Install bolts (6) and bolts (5).

  5. Install the O-ring seal and the retaining ring on tube assembly (10). Install tube assembly (10).

  6. Install the clamp, bolts (8), and bolts (9). Tighten bolts (8) to a torque of 47 ± 9 N·m (35 ± 7 lb ft). Tighten bolts (9) to a torque of 47 ± 9 N·m (35 ± 7 lb ft).


    Illustration 2g01135600

  7. Install O-ring seals (4) on tube assembly (1). Apply clean engine oil to the O-ring seals.

  8. Install elbow (3) on tube assembly (1). Install tube assembly (1) in the adapter. Position the gasket and elbow (3) on the cylinder block and install bolts (2).

  9. Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".

Information System:

3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Remove
C11 and C13 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Alternator - Remove and Install
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant Compressor Oil - Check
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Install
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Required Tools
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant Recovery
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant System - Flush
3508B, 3512B and 3516B Generator Set Engines Balancer Group (Front) - Remove and Install - 3508B Engine
C11 and C13 Engines for Caterpillar Built Machines Fan Drive Mounting Group - Remove and Install
C32 Marine Engines Event Codes
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Remove
3500B Marine Propulsion Engines Auxiliary Water Pump - Inspect
Particulate Filter for Stationary Engines in Standby Applications{1091}
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Fuel Filter Base - Electric Fuel Priming Pump
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Disassemble
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Assemble
12M and 140 Motor Grader Roading the Machine
345C Excavator Machine System Specifications Boom Cylinder
C11 and C13 Engines for Caterpillar Built Machines Electronic Unit Injector - Install
3500B Marine Propulsion Engines Heat Exchanger - Inspect
2005/01/17 Correction to Engine Speed/Timing Sensor-Calibrate {1912}
3406E, C12, C15 and C18 Marine Engines E015 High Engine Coolant Temperature Derate
3406E, C12, C15 and C18 Marine Engines E017 High Engine Coolant Temperature Warning