C9 Urban Transit Bus Engine Fuel Filter Base - Remove and Install Caterpillar


Fuel Filter Base - Remove and Install
`
C9 Urban Transit Bus Engine [RENR7559]
FUEL SYSTEM
FILTER GP-FUEL
C9 Urban Transit Bus Engine Fuel Filter Base - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
185-3630  Strap Wrench Assembly 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.




    Illustration 1g01137272

  1. Use Tooling (A) to remove fuel filter (5).

  2. Disconnect tube assemblies (1) and (2) from fuel filter base (3). Immediately cap all openings or plug all openings in order to prevent contamination.

  3. Remove bolts (4). Remove fuel filter base (3).

Installation Procedure



    Illustration 2g01137272

  1. Position fuel filter base (3) on the front housing. Install bolts (4).

  2. Connect tube assemblies (1) and (2) to the fuel filter base.

  3. Install fuel filter (5).

Information System:

C32 Marine Engine Sensors and Electrical Components
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Piston Ring Groove - Inspect
C32 Marine Engines Fuel Level Sensor Circuit - Test
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Crankshaft Rear Seal and Wear Sleeve - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Cooling System - Test
C27 and C32 Generator Set Engines E059 Low Engine Coolant Level Warning
C27 and C32 Generator Set Engines E057 Low Engine Coolant Level Derate
3126B Industrial Engines E039 Low Engine Oil Pressure Derate
C32 Marine and Marine Generator Set Engines Cooling System - Check - Overheating
3508C, 3512C and 3516C Marine Engines Crankshaft Front Seal and Wear Sleeve - Install
3508C, 3512C and 3516C Marine Engines Crankshaft Rear Seal and Wear Sleeve - Install
3126B Industrial Engines E025 High Inlet Air Temperature Derate
C9 Urban Transit Bus Engine Unit Injector - Remove
C9 Urban Transit Bus Engine Unit Injector - Install
C27 and C32 Engines Electrical System
3500B High Displacement Generator Set Engines Refill Capacities and Recommendations
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Glow Plugs - Test
C9 Urban Transit Bus Engine Exhaust Manifold - Remove and Install
3500B and 3500C Auxiliary Engines, Generator Set Engines, and Generator Sets Refill Capacities and Recommendations
3508C, 3512C and 3516C Marine Engines Vibration Damper - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0096 - FMI 04
Authorized Classic Machine Models {1000, 7000}
C9 Urban Transit Bus Engine Water Temperature Regulator - Remove and Install
3512B Petroleum Engine Plate Locations and Film Locations