3508C, 3512C and 3516C Marine Engines Vibration Damper - Remove and Install Caterpillar


Vibration Damper - Remove and Install
`
3508C, 3512C and 3516C Marine Engines [KENR6055]
BASIC ENGINE
DAMPER GP
3508C, 3512C and 3516C Marine Engines Vibration Damper - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
439-3938  Lifting Bracket 
Guide Stud
1 - 14 by 10 inch 


    Illustration 1g01137704

  1. Remove two bolts (1) and install Tooling (B).

  2. Remove two bolts (3) and attach Tooling (A) and a suitable lifting device to vibration damper (2). The weight of vibration damper (2) is approximately 175 kg (385 lb). Remove remaining bolts (1). Remove vibration damper (2).

Installation Procedure

Table 2
Required Tools 
Tool  Part Number  Part Description  Qty 
439-3938  Lifting Bracket 
Guide Stud
1 - 14 by 10 inch 
Loctite 243 


    Illustration 2g01137704

  1. Install Tooling (B) in the crankshaft.

  2. Attach Tooling (A) and a suitable lifting device to vibration damper (2). The weight of vibration damper (2) is approximately 175 kg (385 lb).

  3. Install the vibration damper on Tooling (B). Install bolts (1). Remove Tooling (B) and install remaining bolts (1). Tighten bolts (1) to a torque of 1125 ± 100 N·m (820 ± 74 lb ft).

  4. Remove Tooling (A). Apply Tooling (C) to the threads of bolts (3). Install bolts (3) and tighten to a torque of 55 ± 7 N·m (41 ± 5 lb ft).

Information System:

3500B and 3500C Auxiliary Engines, Generator Set Engines, and Generator Sets Refill Capacities and Recommendations
C9 Urban Transit Bus Engine Exhaust Manifold - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Glow Plugs - Test
3500B High Displacement Generator Set Engines Refill Capacities and Recommendations
C27 and C32 Engines Electrical System
C9 Urban Transit Bus Engine Unit Injector - Install
C9 Urban Transit Bus Engine Unit Injector - Remove
C9 Urban Transit Bus Engine Fuel Filter Base - Remove and Install
C32 Marine Engine Sensors and Electrical Components
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Piston Ring Groove - Inspect
C32 Marine Engines Fuel Level Sensor Circuit - Test
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Crankshaft Rear Seal and Wear Sleeve - Remove
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0096 - FMI 04
Authorized Classic Machine Models {1000, 7000}
C9 Urban Transit Bus Engine Water Temperature Regulator - Remove and Install
3512B Petroleum Engine Plate Locations and Film Locations
3512B Petroleum Engine Refill Capacities and Recommendations
C6.6 Marine Generator Set Aftercooler Condensate Drain Valve - Inspect/Clean
C11 and C15 Engines for Caterpillar Built Machines E360 Low Engine Oil Pressure
C9.3 Marine Auxiliary Engines Zinc Rods - Inspect/Replace
3512B Petroleum Engine Specifications
C32 Marine Auxiliary Engine Diagnostic Flash Code Retrieval
3508B, 3512B and 3516B Generator Set Engines Alternator - Remove and Install - Alternator and Mounting Group
3126B Engine for Caterpillar Built Machines Engine Oil Pan