14L Motor Grader Exhaust Elbow - Remove and Install Caterpillar


Exhaust Elbow - Remove and Install
`
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

  1. If reusing the exhaust elbow, and or the bellows, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".


    Illustration 1g03507038

  2. loosen ball clamp (1).


    Illustration 2g03507043

  3. Disconnect nitrogen oxide sensor assembly (5).

  4. Loosen clamps (3) and (4).

    Note: Mark the orientation of clamp assembly (4) prior to removal.

  5. Slide elbow (6) into bellows (2) in order to gain clearance. Remove the bellows assembly.

Installation Procedure

  1. If reusing the exhaust elbow, and or the bellows, refer to Special Instruction, REHS5014, "Reuse Guideline for the Lines Group - Flexpipe on Tier 4 Engines".


    Illustration 3g03507056


    Illustration 4g03507057
    Alignment wrap (A) is not shown for photographic purposes.

    Note: Alignment wrap (A) will be included with the new bellows assembly. The Tooling will be pre-installed on the bellows.

    Note: The alignment wrap (A) should not be removed until Step 11. Bellows (2) should never be flexed during installation.

  2. Distance (X) is 40 mm (1.6 inch). Place Mark (B) onto elbow (4). a Distance (X) from the end of elbow (6).

  3. Insert elbow (6) into the bellows. The elbow should be inserted as far as possible without using force. This action will minimize the overall length of the bellows assembly and will help with installation.


    Illustration 5g03507091
    Alignment wrap (A) is not shown for photographic purposes.


    Illustration 6g03507100
    The photo is a cutaway view of the ball clamp assembly.


    Illustration 7g03507101
    The photo is a cutaway view of the ball clamp assembly.

  4. Prior to installation, position both ball clamp assemblies (1) and (3) onto the bellows assembly.

  5. Position the bellows assembly between the Clean Emissions Module and the turbocharger adapter. Adjust the length of elbow (6) in the slip joint at clamp assembly (4) in order to position the bellows assembly.

  6. Verify that the cup of the Ball Joint (E) does not touch the radius of the Ball (D). Position ball clamp (1) and hand tighten ball clamp (1). Measure Distance (Y) and Distance (Z). The two measurements should be equal. Repeat the measurements every 90° around ball clamp (1). If necessary, adjust ball clamp (1).

  7. Repeat Step 6 for ball clamp (3) which is located near the turbocharger.

  8. Verify that Mark (B) is not visible at the slip joint that is positioned near clamp assembly (4).

    Note: Do not use power tools in order to torque clamp assemblies (1), (3), and (4).

  9. Torque ball clamp (1) to a torque of 35 ± 2 N·m (26 ± 1 lb ft).

  10. Torque ball clamp (3) to a torque of 35 ± 2 N·m (26 ± 1 lb ft).

  11. Remove alignment wrap (A) from bellows (2).

  12. Torque clamp assembly (4) to a torque of 55 ± 8 N·m (41 ± 6 lb ft).


    Illustration 8g03507133

  13. Install nitrogen oxide sensor assembly (5). Tighten NOx sensor (5) to a torque of 50 ± 10 N·m (37 ± 7 lb ft).

Information System:

C175-16 Locomotive Engine Fuel Flow Is High
558 Forest Machine Machine Systems Pilot Valve (Joystick)
G3600 A4 Engines Data Link Configuration Status - Test
G3600 A4 Engines Data Link - Test
14L Motor Grader Diesel Exhaust Fluid Tank - Remove and Install
G3600 A4 Engines Detonation - Test
C4.4 and C7.1 Engines Sensor Signal (Analog, Active) - Test
XQP60 and XQP100 Rental Generator Sets Model View Illustrations
C280-08 Tier 4 Engine Temperature Sensor (DEF Manifold) - Remove and Install
G3600 A4 Engines Oil Temperature Is High
Loss of Fuel Prime Causing Hard Start Issues in Certain 3456, C15, and C18 Generator Set Engines{1258, 1261, 1262}
G3600 A4 Engines Oil Pressure Is Low
Product Link E640 System ECM - Configure
Product Link E640 System Configuration File - Install
G3500H Generator Set Engine Valve Lash and Valve Bridge Adjustment
2013/11/13 A New Front Cover Used On Certain C11 and C13 Industrial Engines {1151, 1162, 1206}
C4.4 and C7.1 Engines Sensor Calibration Required - Test
14L Motor Grader Temperature Sensor (DPF Inlet, Flame Detect) - Remove and Install
Three60 Precision Control System Programmable Parameters
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders Location of Components (Steering System)
C15 and C18 On-Highway Engines Fuel Priming Pump - Remove and Install
3500 Petroleum Engines and Petroleum Generator Sets Gauges and Indicators
C15 and C18 On-Highway Engines Fuel Filter Base - Remove and Install - Secondary
C15 and C18 On-Highway Engines Fuel Transfer Pump - Remove and Install