C15 and C18 On-Highway Engines Fuel Filter Base - Remove and Install - Secondary Caterpillar


Fuel Filter Base - Remove and Install - Secondary
`
C15 and C18 On-Highway Engines [UENR3300]
FUEL SYSTEM
FILTER GP-FUEL
C15 and C18 On-Highway Engines Fuel Filter Base - Remove and Install - Secondary
2.1. Removal Procedure
3.1. Installation Procedure

Specifications



Illustration 1g06045286
(A) Length 11 mm (0.4 inch)

Table 1
Specifications for 213-0064 Base As 
Item  Qty  Part  Specification Description 
9S-4167 Hollow Stud  Apply red Loctite 271 to a length of (A) to the threads.
Torque to 70 ± 15 N·m (52 ± 11 lb ft)

Removal Procedure

Table 2
Required Tools 
Tool  Part Number  Part Description  Qty 
185-3630  Strap Wrench As 


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.

Dispose of all fluids according to local regulations and mandates.


  1. Turn the fuel supply to the OFF position and turn the power disconnect switch to the OFF position.


    Illustration 2g02080637

  2. Disconnect harness assemblies (1).

  3. Use Tooling (A) in order to remove fuel filters (5) from fuel filter base (3).

  4. Disconnect tube assemblies (2).

  5. Remove bolts (4) and remove fuel filter base (3).

Installation Procedure


    NOTICE

    Inspect the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.


  1. Install fuel filter base (3) in the reverse order of removal.

    1. Lubricate the seal that is found on the fuel filter with the fluid that is being sealed. Use Tooling (A) in order to tighten fuel filters (5) to a torque of 35 ± 3 N·m (26 ± 2 lb ft).

Information System:

3500 Petroleum Engines and Petroleum Generator Sets Gauges and Indicators
C15 and C18 On-Highway Engines Fuel Priming Pump - Remove and Install
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders Location of Components (Steering System)
Three60 Precision Control System Programmable Parameters
14L Motor Grader Temperature Sensor (DPF Inlet, Flame Detect) - Remove and Install
C4.4 and C7.1 Engines Sensor Calibration Required - Test
2013/11/13 A New Front Cover Used On Certain C11 and C13 Industrial Engines {1151, 1162, 1206}
G3500H Generator Set Engine Valve Lash and Valve Bridge Adjustment
Product Link E640 System Configuration File - Install
Product Link E640 System ECM - Configure
14L Motor Grader Exhaust Elbow - Remove and Install
C175-16 Locomotive Engine Fuel Flow Is High
C15 and C18 On-Highway Engines Fuel Transfer Pump - Remove and Install
C15 and C18 On-Highway Engines Fuel Pressure Regulator - Remove and Install
C15 and C18 On-Highway Engines Fuel Manifold (ARD) - Remove and Install
C15 and C18 On-Highway Engines Exhaust Cooler (NRS) - Remove and Install
C15 and C18 On-Highway Engines Electronic Unit Injector - Remove and Install
C15 and C18 On-Highway Engines Electronic Unit Injector Sleeve - Remove and Install
C15 and C18 On-Highway Engines Turbocharger - Remove and Install
C15 and C18 On-Highway Engines Air Control Valve - Remove and Install
C15 and C18 On-Highway Engines Exhaust Gas Valve (NRS) - Assemble
C15 and C18 On-Highway Engines Solenoid Valve (ARD Main Fuel) - Remove and Install
C15 and C18 On-Highway Engines Exhaust Manifold - Remove and Install
14L Motor Grader Pressure Sensor (ARD Main Fuel) - Remove and Install