C15 and C18 On-Highway Engines Engine Oil Filter Base - Remove and Install - C18 Caterpillar


Engine Oil Filter Base - Remove and Install - C18
`
C15 and C18 On-Highway Engines [UENR3300]
LUBRICATION SYSTEM
FILTER GP-ENGINE OIL
C15 and C18 On-Highway Engines Engine Oil Filter Base - Remove and Install - C18
C15 and C18 On-Highway Engines Engine Oil Filter Base - Remove and Install - C15
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
185-3630  Strap Wrench As 

Start By:

  1. Remove the engine oil cooler.


    Illustration 1g03520362

  1. Disconnect hose assembly (1).

  2. Use Tooling (A) in order to remove oil filters (4). Drain the oil from the oil filters into a suitable container for storage or for disposal. Discard the filters.

  3. Remove bolts (2) and remove oil filter base (3).

    ------ WARNING! ------

    Personal injury can result from being struck by parts propelled by a released spring force.

    Make sure to wear all necessary protective equipment.

    Follow the recommended procedure and use all recommended tooling to release the spring force.




    Illustration 2g03520363

  4. Remove plug (5), spring (6) and plunger (7).

  5. Remove plug (10), spring (9) and plunger (8).

Installation Procedure

    Note: Inspect the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.

  1. Install engine oil filter base (3) in the reverse order of removal.

    1. Apply clean engine oil to the seal which is found on oil filter assemblies (4). Hand tighten oil filters (4) until the seal contacts the sealing surface of the oil filter base (3). Tighten oil filters (4) to an additional turn of 270 degrees. Change the engine oil. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change".

Information System:

G3500H Generator Set Engine Air/Fuel Ratio Control - NO<SUB>X</SUB> Feedback
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders Blade Cushion - If Equipped
2013/11/13 New Exhaust Temperature Sensor Groups Are Used on Certain 3500, 3600, C175, and C280 Marine and Petroleum Off-Shore Applications {1408, 1900, 1906, 1919, 1921, 1922, 1928, 1929, 7498}
C15 and C18 On-Highway Engines Engine Oil Cooler - Remove and Install - C15
C15 and C18 On-Highway Engines Engine Oil Cooler - Remove and Install - C18
C280-08 Marine Engine After Stopping Engine
Installation Procedure For The New Throttle Body Cooling Lines On Certain G3500 Engines{1380}
C280-12 Marine Engine Engine Power Ratings
CX31-P600 Petroleum Transmission Transmission Planetary
CX31-P600 Petroleum Transmission General Information
C15 and C18 On-Highway Engines Air Inlet Elbow - Remove and Install
C9 Petroleum Engine Product Description
G3500H Generator Set Engine Lubrication System
C15 and C18 On-Highway Engines Engine Oil Filter Base - Remove and Install - C15
G3500H Generator Set Engine Cooling System
Reuse and Salvage for Engine Dampers {1202, 1205}
C15 and C18 On-Highway Engines Engine Oil Pump - Remove and Install
2014/02/20 New Anti Drift Valves are Now Used on Certain 345D and 349D Excavators {5059}
CX31-P600 Petroleum Transmission Visual Inspection
CX31-P600 Petroleum Transmission Torque Converter Troubleshooting
C15 and C18 On-Highway Engines Water Temperature Regulator Housing - Remove and Install
CX31-P600 Petroleum Transmission Transmission Planetary Troubleshooting
C15 and C18 On-Highway Engines Flywheel - Remove and Install
CX31-P600 Petroleum Transmission Hydraulic Oil Contamination - Test