C280-16 Engine Exhaust Manifold Shield - Remove and Install Caterpillar


Exhaust Manifold Shield - Remove and Install
`
C280-16 Engine [UENR3297]
AIR INLET AND EXHAUST SYSTEM
MANIFOLD GP-EXHAUST
C280-12 and C280–16 Marine Engines Exhaust Manifold - Remove and Install - C280-16
C280-16 Engine Exhaust Manifold Shield - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Handle the shields carefully. Do not tear the stainless steel foil inside the heat shields.




    Illustration 1g03523580

  1. Disconnect hose assembly (1) and remove fitting (2).


    Illustration 2g03523942

  2. Remove shield assembly (3) and covers (4).


    Illustration 3g03524601


    Illustration 4g03524639

  3. Remove cover (5) and cover (6).

  4. Remove brackets (7) and covers (8).


    Illustration 5g03524662

  5. Remove shield assemblies (9).


    Illustration 6g03525438

  6. Remove bolts (11) and cover (10).


    Illustration 7g03525557


    Illustration 8g03525620

  7. Remove bracket (12) and cover (13). Remove cover (14).


    Illustration 9g03525937

  8. Remove cover (17), cover (16), then cover (15).


    Illustration 10g03525997

  9. Remove bracket assembly (18).


    Illustration 11g03526050


    Illustration 12g03526143

  10. Remove cover (21), cover (20), then cover (19).

  11. Remove cover (23) then cover (22).


    Illustration 13g03526185


    Illustration 14g03526258

  12. Remove bracket assembly (24). Remove cover (25).


NOTICE

Do not use flammable liquid in order to clean the stainless steel foil inside of the heat shield. Use only water and detergent. Flammable liquid can saturate the insulation material and cause a fire when the engine temperature rises.


Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Handle the shields carefully. Do not tear the stainless steel foil inside the heat shields.


  1. Install exhaust manifold shield in the reverse order of removal.

Information System:

C15 and C18 On-Highway Engines Cylinder Head - Remove and Install
C15 and C18 On-Highway Engines Rocker Arm and Shaft - Remove and Install
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and 160 Motor Graders Solenoid Valve - Test
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders Hydraulic System
C15 and C18 On-Highway Engines Crankshaft Front Seal - Remove and Install
C15 and C18 On-Highway Engines Power Take-Off Drive Group - Assemble
C15 and C18 On-Highway Engines Flywheel Housing - Remove and Install - Power Take Off equipped
C280 Marine Engines Battery
CX31-P600 Petroleum Transmission Hydraulic Oil Contamination - Test
C15 and C18 On-Highway Engines Flywheel - Remove and Install
CX31-P600 Petroleum Transmission Transmission Planetary Troubleshooting
C15 and C18 On-Highway Engines Water Temperature Regulator Housing - Remove and Install
3516C Marine Engine Catalyst (SCR) - Replace
Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479}
3516C Marine Engine Model View Illustrations
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Water in Fuel - Test
C15 and C18 On-Highway Engines Engine Oil Pan - Remove and Install
TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400}
C11 and C13 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
140, 150, 160, 12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Service Interval Chart
C175 Oil Pressure Regulator Inspection and Rework{1304, 5117}
793F Tier IV Off-Highway Truck Field Assembly Films - Install