C15 and C18 On-Highway Engines Engine Oil Pan - Remove and Install Caterpillar


Engine Oil Pan - Remove and Install
`
C15 and C18 On-Highway Engines [UENR3300]
BASIC ENGINE
PAN GP-OIL
C15 and C18 On-Highway Engines Engine Oil Pan - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure



    Illustration 1g02162853

  1. Remove drain plugs (1) and (2). Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct draining and filling procedures. Remove the O-ring seal from the drain plugs.

  2. Remove bolts (3) and remove oil pan (4).

Installation Procedure

  1. Install engine oil pan (4) in reverse order of removal.


      Illustration 2g02162853


      Illustration 3g03524317
      Tightening Sequence

    1. Tighten bolts (3) in the sequence shown in Illustration 3 to a torque of 40 ± 5 N·m (30 ± 7 lb ft).


      Illustration 4g03524498
      Retightening Sequence

    2. Retighten bolts (3) in the sequence shown in Illustration 4 to a torque of 47 ± 5 N·m (35 ± 4 lb ft).

    3. Tighten drain plugs (1) to a torque of 70 ± 15 N·m (52 ± 11 lb ft).

    4. Tighten drain plugs (2) to a torque of 90 ± 15 N·m (66 ± 11 lb ft).

Information System:

C13, C15, and C18 Tier 4 Final Engines Water in Fuel - Test
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C15 and C18 On-Highway Engines Camshaft - Remove and Install
3516C Marine Engine Model View Illustrations
Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479}
3516C Marine Engine Catalyst (SCR) - Replace
C280-16 Engine Exhaust Manifold Shield - Remove and Install
C15 and C18 On-Highway Engines Cylinder Head - Remove and Install
C15 and C18 On-Highway Engines Rocker Arm and Shaft - Remove and Install
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and 160 Motor Graders Solenoid Valve - Test
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders Hydraulic System
C15 and C18 On-Highway Engines Crankshaft Front Seal - Remove and Install
TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400}
C11 and C13 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
140, 150, 160, 12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Service Interval Chart
C175 Oil Pressure Regulator Inspection and Rework{1304, 5117}
793F Tier IV Off-Highway Truck Field Assembly Films - Install
793F Tier IV Off-Highway Truck Field Assembly Wheel Chock - Install
C280-08 Marine Engine Plate Locations and Film Locations
C15 and C18 On-Highway Engines Vibration Damper and Pulley - Remove and Install
C4.4 Engines for Caterpillar Built Machines Connecting Rod - For Use With Spheroidal Graphite Iron (SGI) Crankshaft
C15 and C18 On-Highway Engines Front Cover - Remove and Install
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders Centershift Lock
C11 and C13 On-Highway Engines Compression Brake Lash - Adjust