C11 and C13 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install Caterpillar


Valve Actuator (Variable) - Remove and Install
`
C11 and C13 Engines for Caterpillar Built Machines [RENR9214]
BASIC ENGINE
VALVE MECHANISM GP
C11 and C13 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure

Removal Procedure

Start By:

  1. Remove the valve cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".

Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and helps to keep contaminants from entering the system.

Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be cleaned thoroughly. This will help to prevent dirt from entering the internal mechanism.




    Illustration 1g01265475

  1. Disconnect harness assemblies (3) . Remove bolts (1) and nuts (2) . Remove valve actuator (4) .

Installation Procedure

Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.

Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.




    Illustration 2g01265475

  1. Position valve actuator (4) . Install bolts (1) and nuts (2) . Tighten bolts (1) and nuts (2) to a torque of 100 ± 20 N·m (74 ± 15 lb ft). Connect harness assemblies (3) .

  1. Adjust the valve actuators. Refer to Testing and Adjusting, "Compression Brake Lash- Adjust" for the proper procedure.

End By: Install the valve cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".

Information System:

TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400}
C15 and C18 On-Highway Engines Engine Oil Pan - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Water in Fuel - Test
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C15 and C18 On-Highway Engines Camshaft - Remove and Install
3516C Marine Engine Model View Illustrations
Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479}
3516C Marine Engine Catalyst (SCR) - Replace
C280-16 Engine Exhaust Manifold Shield - Remove and Install
C15 and C18 On-Highway Engines Cylinder Head - Remove and Install
C15 and C18 On-Highway Engines Rocker Arm and Shaft - Remove and Install
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and 160 Motor Graders Solenoid Valve - Test
140, 150, 160, 12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Service Interval Chart
C175 Oil Pressure Regulator Inspection and Rework{1304, 5117}
793F Tier IV Off-Highway Truck Field Assembly Films - Install
793F Tier IV Off-Highway Truck Field Assembly Wheel Chock - Install
C280-08 Marine Engine Plate Locations and Film Locations
C15 and C18 On-Highway Engines Vibration Damper and Pulley - Remove and Install
C4.4 Engines for Caterpillar Built Machines Connecting Rod - For Use With Spheroidal Graphite Iron (SGI) Crankshaft
C15 and C18 On-Highway Engines Front Cover - Remove and Install
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders Centershift Lock
C11 and C13 On-Highway Engines Compression Brake Lash - Adjust
Exhaust Balance Valve Causing Regeneration Issues On Certain Tier 4i C13 Engines{1061, 5479}
C280-16 Engine Prelubrication Oil Pump - Remove and Install