2005/04/25 Cover Plate, Flange are Available for Use During Flow Tests on the Main Hydraulic Pumps {0738, 5070, 5084} Caterpillar


Cover Plate, Flange are Available for Use During Flow Tests on the Main Hydraulic Pumps {0738, 5070, 5084}
`
2005/04/25 [SEPD0781]
HYDRAULIC SYSTEM
PUMP GP
2005/04/25 Cover Plate, Flange are Available for Use During Flow Tests on the Main Hydraulic Pumps {0738, 5070, 5084}
AVSpare Products:
  • All



  • Illustration 1g01157067

    7I-7133 Cover Plate




    Illustration 2g01157068

    7I-7151 Flange

    Dealer Service Tools offers the 7I-7133 Cover Plate and the 7I-7151 Flange for use during flow tests on the main hydraulic pumps for most AVSpare machines.

    The 7I-7133 Cover Plate blocks a port for the test. The 7I-7151 Flange has a No. 16 port for plumbing in a flow meter.

    Table 1
    Specifications for Cover Plate and Flange    
    Plate Dimensions     Bolt Hole Dimensions     Thread Specifications    
    7I-7133 Cover Plate    

    96.7 X 61.8 X 18 mm (3.81 X 2.43 X 0.71 inch)    
    4 holes with centers located on corners of
    66.7 X 31.8 mm (2.63 X 1.25 inch) rectangle    
    Bolt holes M12 X 1.75 X 6H THD    
    7I-7151 Flange    

    98 X 70 X 22 mm (3.9 X 2.8 X 0.9 inch)    
    4 holes with enters located on corners of
    77.8 X 42.9 mm (3.06 X 1.69 inch) rectangle    
    No thread on bolt holesNo.16 port with 1-5/16-12-2B THD    

    Information System:

    C1.5 GEN SET Electric Power Generation Refill Capacities and Recommendations
    120M, 12M, 140M, 160M, 140, 150 and 160 Motor Graders Governor (Air Compressor) - Test and Adjust
    Electronic Installation Guide{1000}
    Reuse and Salvage for Cast Iron Cylinder Blocks {0679, 1201, 1201}
    2005/02/21 Information Release Memo, PELJ0481 , "Product Line Expansion for Caterpillar Low and Medium Pressure Hose and Coupling Products" {5057}
    120M, 12M, 140M, 160M, 140, 150 and 160 Motor Graders Drawbar
    C9 Urban Transit Bus Engine Air Compressor - Remove and Install
    3500 Petroleum Engines and Petroleum Generator Sets Control Panel
    2005/01/31 Improved Lifters are Now Used {1102, 1121, 1123}
    C9 Urban Transit Bus Engine Idler Pulley - Remove and Install
    3516C HD Petroleum Well Service Engine Reference Material
    C11 and C13 Engines Engine Oil Level Switch - If Equipped
    DE Series Generator Set with Cat C1.1, C1.5, and C2.2 Engines Generator Lead Connections
    3508C, 3512C and 3516C Marine Engines Auxiliary Water Pump - Remove
    Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736}
    3500 Engines Auxiliary Water Pump - Disassemble
    3500 Engines Auxiliary Water Pump - Assemble
    3508B, 3512B and 3516B Generator Set Engines Exhaust Elbow - Remove and Install
    3126B Engines Cooling System - Check - Overheating
    374F Excavator Bucket Linkage - Inspect/Adjust
    C15 and C18 Engines for Caterpillar Built Machines Diagnostic Codes
    C27 and C32 Generator Set Engines E194 High Exhaust Temperature
    C27 and C32 Generator Set Engines E361 High Engine Coolant Temperature
    C27 and C32 Generator Set Engines E360 Low Engine Oil Pressure